Volvo All Engines (2004 Emissions) Fault Code: PID 175 FMI 0 Engine Oil Temperature / Temperature Sensor
Fault Condition: The Electronic Malfunction Lamp (EML) will turn on and PID 175 will set if the engine oil temperature signal voltage is less than .17 volts or greater than 4.92 volts. If the EMS Module senses that the engine oil temperature signal is critically above range, FMI code 0 will be set. If the engine oil temperature reaches 259°F (126°C), the engine power will be reduced by 15%. If the engine oil temperature reaches 262°F (128°C), the engine will be shutdown. Yellow or red warning lamp identification and buzzer warning will accompany the extreme engine oil temperature conditions. If the reference voltage signal is shorted to ground FMI 4 will be set. If the reference voltage circuit is shorted to battery voltage or has an open circuit, FMI 5 will be set. If the ground circuit of the sensor has an open, FMI 5 will also be set.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect the Engine Oil Level/Temperature Sensor connector. Check for continuity between pin 1 of the Engine Oil Temperature/Level Sensor and a good ground. Check for continuity between pin 2 of the Engine Oil Temperature/Level Sensor and a good ground. Check for continuity between pin 3 of the Engine Oil Temperature/Level Sensor and a good ground. Check for continuity between pin 4 of the Engine Oil Temperature/Level Sensor and a good ground. If continuity exists between any of the pins and ground, replace the Engine Oil Level/Temperature Sensor.
2) Disconnect the Engine Oil Level/Temperature Sensor connector. Measure the resistance across the pins 3 and 4 of the Engine Oil Temperature/Level Sensor. If the resistance of the sensor is NOT as specified, replace the replace the Engine Oil Level/Temperature Sensor.
3) Disconnect the Engine Oil Level/Temperature Sensor harness connector. Turn the ignition key ON. Measure voltage between Engine Oil Level/Temperature Sensor harness connector pin 3 and a good ground.
If the measured voltage is more than 4.5 volts, verify the diagnostic code, the FMI and retest. If FMI 4 is still active, replace the Engine Management System (EMS) Module and retest the system.
4) Disconnect the Engine Oil Level/Temperature Sensor harness connector. Disconnect the EMS Module harness connector A. Measure continuity between Engine Oil Level/Temperature Sensor harness connector pin 3 and a good ground. If continuity exists, repair the short to ground between in the signal line voltage circuit. If there is NO continuity, check the pins or the EMS Module for dirt, loose pins or deformed contacts. Replace the EMS Module if the pins of the module are not damaged. Retest the system.
5) Disconnect the Engine Oil Level/Temperature Sensor harness connector. Disconnect the EMS Module harness connector A. Turn the ignition key ON. Measure voltage between Engine Oil Level/Temperature Sensor harness
connector pin 3 and a good ground. If the there is voltage present, repair the short to voltage on the signal line.
6) Disconnect the Engine Oil Level/Temperature Sensor connector. Disconnect connector A from the EMS Module. Check for continuity between connector A pin 11 and/or 31 of the EMS Module harness connector and pin 3 of the Engine Oil Level/Temperature Sensor harness connector. If there is NO continuity, locate and repair the open in the circuit between the Engine Oil Level/Temperature Sensor and the EMS Module.
7) Visually inspect the EMS Module harness connectors A and B for dirt, loose pins or deformed contacts. If a repairable open is found or any of the pins feel loose, repair the EMS Module harness connector.
If an open is not found and the EMS Module harness connector has a good contact, verify the diagnostic code, the FMI and retest. If FMI 5 is still active, replace the Engine Management System (EMS) Module and retest the system.
Related
-
JPRO 2022 v1 Commercial Vehicle Diagnostics V1 Software Download & Installation Service ( 1 PC )
JPRO $94.00Rated 0 out of 5 -
download MANCATS II v14.01 2014 Diagnostic software MAN CATS ( virtual machine )
MAN $75.00Rated 0 out of 5 -
Scania SDP3 2.48.6 Diagnosis & Programming for VCI 3 VCI3 without Dongle
Scania $30.00Rated 0 out of 5
-
Bobcat Service Library [03.2019] Service, Operator, Maintenance, Bulletines, etc full update
Bobcat $110.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5 -
download MANCATS II v14.01 2014 Diagnostic software MAN CATS ( virtual machine )
MAN $75.00Rated 0 out of 5 -
PF Diagnose 2.0.2.23 Diagnostics Software 2013 – Full Heavy & Medium Duty with OBDII Support – Online Installation Service
PF Diagnose $60.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL INTERNATIONAL ENGINE VT275 (2005 & Newer)
INTERNATIONAL ENGINES $27.00Rated 0 out of 5 -
SERVICE MANUAL International Engines DT466E & DT530E (1999 & Older)
INTERNATIONAL ENGINES $31.00Rated 0 out of 5