Volvo All Engines (2004 Emissions) Fault Code: PID 175 FMI 0 Engine Oil Temperature / Temperature Sensor
Fault Condition: The Electronic Malfunction Lamp (EML) will turn on and PID 175 will set if the engine oil temperature signal voltage is less than .17 volts or greater than 4.92 volts. If the EMS Module senses that the engine oil temperature signal is critically above range, FMI code 0 will be set. If the engine oil temperature reaches 259°F (126°C), the engine power will be reduced by 15%. If the engine oil temperature reaches 262°F (128°C), the engine will be shutdown. Yellow or red warning lamp identification and buzzer warning will accompany the extreme engine oil temperature conditions. If the reference voltage signal is shorted to ground FMI 4 will be set. If the reference voltage circuit is shorted to battery voltage or has an open circuit, FMI 5 will be set. If the ground circuit of the sensor has an open, FMI 5 will also be set.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect the Engine Oil Level/Temperature Sensor connector. Check for continuity between pin 1 of the Engine Oil Temperature/Level Sensor and a good ground. Check for continuity between pin 2 of the Engine Oil Temperature/Level Sensor and a good ground. Check for continuity between pin 3 of the Engine Oil Temperature/Level Sensor and a good ground. Check for continuity between pin 4 of the Engine Oil Temperature/Level Sensor and a good ground. If continuity exists between any of the pins and ground, replace the Engine Oil Level/Temperature Sensor.
2) Disconnect the Engine Oil Level/Temperature Sensor connector. Measure the resistance across the pins 3 and 4 of the Engine Oil Temperature/Level Sensor. If the resistance of the sensor is NOT as specified, replace the replace the Engine Oil Level/Temperature Sensor.
3) Disconnect the Engine Oil Level/Temperature Sensor harness connector. Turn the ignition key ON. Measure voltage between Engine Oil Level/Temperature Sensor harness connector pin 3 and a good ground.
If the measured voltage is more than 4.5 volts, verify the diagnostic code, the FMI and retest. If FMI 4 is still active, replace the Engine Management System (EMS) Module and retest the system.
4) Disconnect the Engine Oil Level/Temperature Sensor harness connector. Disconnect the EMS Module harness connector A. Measure continuity between Engine Oil Level/Temperature Sensor harness connector pin 3 and a good ground. If continuity exists, repair the short to ground between in the signal line voltage circuit. If there is NO continuity, check the pins or the EMS Module for dirt, loose pins or deformed contacts. Replace the EMS Module if the pins of the module are not damaged. Retest the system.
5) Disconnect the Engine Oil Level/Temperature Sensor harness connector. Disconnect the EMS Module harness connector A. Turn the ignition key ON. Measure voltage between Engine Oil Level/Temperature Sensor harness
connector pin 3 and a good ground. If the there is voltage present, repair the short to voltage on the signal line.
6) Disconnect the Engine Oil Level/Temperature Sensor connector. Disconnect connector A from the EMS Module. Check for continuity between connector A pin 11 and/or 31 of the EMS Module harness connector and pin 3 of the Engine Oil Level/Temperature Sensor harness connector. If there is NO continuity, locate and repair the open in the circuit between the Engine Oil Level/Temperature Sensor and the EMS Module.
7) Visually inspect the EMS Module harness connectors A and B for dirt, loose pins or deformed contacts. If a repairable open is found or any of the pins feel loose, repair the EMS Module harness connector.
If an open is not found and the EMS Module harness connector has a good contact, verify the diagnostic code, the FMI and retest. If FMI 5 is still active, replace the Engine Management System (EMS) Module and retest the system.
Related
-
10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C
CAT $110.00Rated 0 out of 5 -
PF Diagnose 2.0.2.23 Diagnostics Software 2013 – Full Heavy & Medium Duty with OBDII Support – Online Installation Service
PF Diagnose $60.00Rated 0 out of 5
-
10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C
CAT $110.00Rated 0 out of 5 -
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2
Trucks software $35.00Rated 0 out of 5 -
DPF EGR SCR BAC ERG Delete & Flash CAAT Cummings Detroit Dodge Mack Volvo Collection of DELETE files
CAT $200.00Rated 0 out of 5 -
DETROIT DDDL 8.14 SP3 – Detroit Diesel Diagnostic Link 8.14 SP3 2021 ( 1PC )
Detroit $73.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5 -
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5 -
premium volvo tech tool update 2.8.150 diagnostic software 1pc
Trucks software $150.00Rated 0 out of 5 -
Navistar international OnCommand service information 2018 software trucks
Navistar $50.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce 7 (2010 & Newer)
INTERNATIONAL ENGINES $34.00Rated 0 out of 5 -
SERVICE MANUAL International Engines DT466 & DT530 (2001-2003) C
INTERNATIONAL ENGINES $31.00Rated 0 out of 5