Volvo All Engines (2004 Emissions) Fault Code: PID 175 FMI 0 Engine Oil Temperature / Temperature Sensor
Fault Condition: The Electronic Malfunction Lamp (EML) will turn on and PID 175 will set if the engine oil temperature signal voltage is less than .17 volts or greater than 4.92 volts. If the EMS Module senses that the engine oil temperature signal is critically above range, FMI code 0 will be set. If the engine oil temperature reaches 259°F (126°C), the engine power will be reduced by 15%. If the engine oil temperature reaches 262°F (128°C), the engine will be shutdown. Yellow or red warning lamp identification and buzzer warning will accompany the extreme engine oil temperature conditions. If the reference voltage signal is shorted to ground FMI 4 will be set. If the reference voltage circuit is shorted to battery voltage or has an open circuit, FMI 5 will be set. If the ground circuit of the sensor has an open, FMI 5 will also be set.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect the Engine Oil Level/Temperature Sensor connector. Check for continuity between pin 1 of the Engine Oil Temperature/Level Sensor and a good ground. Check for continuity between pin 2 of the Engine Oil Temperature/Level Sensor and a good ground. Check for continuity between pin 3 of the Engine Oil Temperature/Level Sensor and a good ground. Check for continuity between pin 4 of the Engine Oil Temperature/Level Sensor and a good ground. If continuity exists between any of the pins and ground, replace the Engine Oil Level/Temperature Sensor.
2) Disconnect the Engine Oil Level/Temperature Sensor connector. Measure the resistance across the pins 3 and 4 of the Engine Oil Temperature/Level Sensor. If the resistance of the sensor is NOT as specified, replace the replace the Engine Oil Level/Temperature Sensor.
3) Disconnect the Engine Oil Level/Temperature Sensor harness connector. Turn the ignition key ON. Measure voltage between Engine Oil Level/Temperature Sensor harness connector pin 3 and a good ground.
If the measured voltage is more than 4.5 volts, verify the diagnostic code, the FMI and retest. If FMI 4 is still active, replace the Engine Management System (EMS) Module and retest the system.
4) Disconnect the Engine Oil Level/Temperature Sensor harness connector. Disconnect the EMS Module harness connector A. Measure continuity between Engine Oil Level/Temperature Sensor harness connector pin 3 and a good ground. If continuity exists, repair the short to ground between in the signal line voltage circuit. If there is NO continuity, check the pins or the EMS Module for dirt, loose pins or deformed contacts. Replace the EMS Module if the pins of the module are not damaged. Retest the system.
5) Disconnect the Engine Oil Level/Temperature Sensor harness connector. Disconnect the EMS Module harness connector A. Turn the ignition key ON. Measure voltage between Engine Oil Level/Temperature Sensor harness
connector pin 3 and a good ground. If the there is voltage present, repair the short to voltage on the signal line.
6) Disconnect the Engine Oil Level/Temperature Sensor connector. Disconnect connector A from the EMS Module. Check for continuity between connector A pin 11 and/or 31 of the EMS Module harness connector and pin 3 of the Engine Oil Level/Temperature Sensor harness connector. If there is NO continuity, locate and repair the open in the circuit between the Engine Oil Level/Temperature Sensor and the EMS Module.
7) Visually inspect the EMS Module harness connectors A and B for dirt, loose pins or deformed contacts. If a repairable open is found or any of the pins feel loose, repair the EMS Module harness connector.
If an open is not found and the EMS Module harness connector has a good contact, verify the diagnostic code, the FMI and retest. If FMI 5 is still active, replace the Engine Management System (EMS) Module and retest the system.
Related
-
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2
Trucks software $35.00Rated 0 out of 5
-
Eaton Service Ranger 4.9 Engineering 4.9 [05.2021] Engineering Level ( 1 PC )
Eaton $67.00Rated 0 out of 5 -
DOWNLOAD Paccar ESA Electronic Service Analyst 5.5.0 Diagnostic Software 2023
PACCAR $96.00Rated 0 out of 5 -
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5 -
Wabco ToolBox plus 13.7.0.1 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5 -
download Hitachi Construction Machinery MPDr Ver 3.7.0.0 [10.2020] Diagnostic Software
Hitachi $76.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5 -
Detroit Diesel Diagnostic Link DDDL 8.0 PRO PROFESSIONAL Software trucks
Detroit $25.00Rated 0 out of 5 -
VOLVO PREMIUM TECH TOOL PTT 2.7.116 + APCI 2021 + devtool ( ONLINE )
Trucks software $80.00Rated 0 out of 5 -
DAF Davie Runtime v5.6.1 Davie XDc ll [02.2019] + Expire Fix 302.00 Unlock ( Windows 7 )
DAF $70.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL DETROIT DIESEL EPA 07, EPA 10, GHG 14 TROUBLESHOOTING
DETROIT $38.00Rated 0 out of 5 -
SERVICE MANUAL INTERNATIONAL ENGINE VT365 (2004 & Newer)
INTERNATIONAL ENGINES $24.00Rated 0 out of 5 -
SERVICE MANUAL Eaton Fuller – Autoshift, Autoselect Service Manual (TRSM-0050)
EATON $25.00Rated 0 out of 5 -
SERVICE MANUAL International Engines VT275 (2004 & Older)
INTERNATIONAL ENGINES $21.00Rated 0 out of 5