Volvo All Engines (2004 Emissions) Fault Code: SID 232 FMI 3 Sensor Supply Voltage #1
Fault Condition: The Electronic Malfunction Lamp (EML) will turn on and code SID 232 will set when the reference voltage to the Electronic Fan Controller, Boost Pressure Sensor and Intake Air Temperature and Humidity Sensor is less than 4.5 volts or greater than 5.5 volts. If the voltage returns to 4.5 volts to 5.5 volts, the fault will become inactive.
Possible repairs:
Turn the ignition key OFF first.
1) If code SID 232 is NOT set, wiggle the harness and connectors to try to set the code. Visually inspect the EMS Module connectors for frayed wires and loose or corroded connections.
2) Disconnect EMS Module connector A. Disconnect the Electronic Fan Controller, Boost Pressure Sensor and Intake Air Temperature and Humidity Sensor harness connectors. Check for continuity between EMS Module harness connector A, pin 7 and a good ground. If continuity exists, locate and repair the short circuit to ground.
3) Disconnect EMS Module connector A. Turn the ignition key ON. Measure the voltage between EMS Module connector A pin 7 and a good ground. If voltage is present, locate and repair the short circuit to voltage in circuit.
4) Disconnect EMS Module connector A. Disconnect the Electronic Fan Controller, Boost Pressure Sensor and Intake Air Temperature and Humidity Sensor harness connectors. Check for continuity between EMS Module
harness connector A, pin 7 and a pin 1 of the Electronic Fan Controller, Boost Pressure Sensor and Intake Air Temperature and Humidity Sensor connectors. If there is NO continuity, locate and repair the open in the circuit.
5) Disconnect EMS Module connector A. Visually inspect both sides of EMS Module connector A. If a repairable short circuit or damaged pins are found, repair or replace the harness connector.
6) Connect EMS Module connector A. Connect the Electronic Fan Controller, Boost Pressure Sensor and Intake Air Temperature and Humidity Sensor harness connectors. Start the engine and recheck for codes. If code SID 232 is still active, replace the EMS Module and retest the system. If code SID 232 is not active, the diagnostic procedures have corrected the problem. Check all connectors to ensure proper connections.
Related
-
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5
-
CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT $45.00Rated 0 out of 5 -
John Deere & Hitachi Parts ADVISOR 2020 [08.2020] Offline DVD Spare Parts Catalog
John Deere $120.00Rated 0 out of 5 -
Bobcat Service Library [03.2019] Service, Operator, Maintenance, Bulletines, etc full update
Bobcat $110.00Rated 0 out of 5 -
International Truck ISIS – Oncommand Service Information Q4.2020 [04.2020]
Navistar $85.00Rated 0 out of 5 -
VOLVO PREMIUM TECH TOOL PTT 2.7.116 + APCI 2021 + devtool ( ONLINE )
Trucks software $80.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5