Volvo All Engines (2004 Emissions) Fault Code: PID 98 FMI 1 Engine Oil Level / Temperature Sensor
Fault Condition: If the EMS Module senses that the engine oil level is moderately or critically below range, FMI 1 will be set. If the reference voltage signal is shorted to ground, FMI 4 will be set. If the reference voltage circuit is shorted to battery voltage or has an open circuit, FMI 5 will be set. If the ground circuit of the sensor has an open, FMI 5 will also be set.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect the Engine Oil Temperature/Level Sensor connector.Check for continuity between each of the pins (1,2,3, and 4) of the Engine Oil Temperature/Level Sensor and a good ground. If continuity exists between any of the pins and ground, replace the Engine Oil Temperature/Level Sensor.
2) Disconnect the Engine Oil Temperature/Level Sensor connector. Measure the resistance across the pins 1 and 2 of the Engine Oil Temperature/Level Sensor. With the engine at room temperature the sensor resistance should be 10.8-17.4 ohms. If the resistance of the sensor is NOT as specified, replace the Engine Oil Temperature/Level Sensor.
3) Disconnect the Engine Oil Temperature/Level Sensor harness connector. Disconnect the EMS Module harness connector B. Measure continuity between Engine Oil Temperature/Level Sensor harness connector pin 2 and a good ground. If continuity exists, repair the short to ground in the signal line circuit. If there is NO continuity, check the pins or the EMS Module for dirt, loose pins or deformed contacts. Replace the EMS Module if the pins of the module are not damaged. Retest the system.
4) Disconnect the Engine Oil Temperature/Level Sensor connector. Measure the resistance across the pins 1 and 2 of the Engine Oil Temperature/Level Sensor. With the engine at room temperature the sensor resistance should be 10.8-17.4 ohms. If the resistance of the sensor is NOT as specified, replace the Engine Oil Temperature/Level Sensor.
5) Disconnect the Engine Oil Temperature/Level Sensor harness connector. Disconnect the EMS Module harness connector B. Turn the ignition key ON. Measure voltage between Engine Oil Temperature/Level Sensor harness
connector pin 2 and a good ground. If the there is voltage present, repair the short to voltage on the signal line.
6) Disconnect the Engine Oil Temperature/Level Sensor connector. Disconnect connector B from the EMS Module. Check for continuity between connector B pin 4 of the EMS Module harness connector and pin 2 of the Engine Oil Temperature/Level Sensor harness connector. If there is NO continuity, locate and repair the circuit between the sensor and the EMS Module.
7) Disconnect the Engine Oil Temperature/Level Sensor connector. Disconnect connector B from the EMS Module. Check for continuity between connector B pin 3 of the EMS Module harness connector and pin 1 of the Engine Oil Temperature/Level Sensor harness connector. If there is NO continuity, locate and repair the circuit between the sensor and the EMS Module.
8) Visually inspect the EMS Module harness connectors A and B for dirt, loose pins or deformed contacts. If a repairable open is found or either of the pins feels loose, repair the EMS Module harness connector.
If the EMS Module harness connector is OK, verify the diagnostic code and the FMI, and retest. If FMI 5 is still active, replace the Engine Management System (EMS) Module and retest the system.
Related
-
DOWNLOAD NISSAN UD DIESEL PC-CONSULT DIAGNOSTIC 1.1.13 & PC-REPROMASTER 1.2.0
NISSAN UD $100.00Rated 0 out of 5 -
premium volvo tech tool update 2.8.150 diagnostic software 1pc
Trucks software $150.00Rated 0 out of 5 -
John Deere & Hitachi Parts ADVISOR 2020 [08.2020] Offline DVD Spare Parts Catalog
John Deere $120.00Rated 0 out of 5
-
CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT $45.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce 7 (2010 & Newer)
INTERNATIONAL ENGINES $34.00Rated 0 out of 5 -
MANUAL SERVICE Deutz Combine 5650 H, 5660 HTS5670 H / HTS5680 H, 5690 HTS
DEUTZ $38.00Rated 0 out of 5