Volvo All Engines (2004 Emissions) Fault Code: PID 98 FMI 1 Engine Oil Level / Temperature Sensor
Fault Condition: If the EMS Module senses that the engine oil level is moderately or critically below range, FMI 1 will be set. If the reference voltage signal is shorted to ground, FMI 4 will be set. If the reference voltage circuit is shorted to battery voltage or has an open circuit, FMI 5 will be set. If the ground circuit of the sensor has an open, FMI 5 will also be set.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect the Engine Oil Temperature/Level Sensor connector.Check for continuity between each of the pins (1,2,3, and 4) of the Engine Oil Temperature/Level Sensor and a good ground. If continuity exists between any of the pins and ground, replace the Engine Oil Temperature/Level Sensor.
2) Disconnect the Engine Oil Temperature/Level Sensor connector. Measure the resistance across the pins 1 and 2 of the Engine Oil Temperature/Level Sensor. With the engine at room temperature the sensor resistance should be 10.8-17.4 ohms. If the resistance of the sensor is NOT as specified, replace the Engine Oil Temperature/Level Sensor.
3) Disconnect the Engine Oil Temperature/Level Sensor harness connector. Disconnect the EMS Module harness connector B. Measure continuity between Engine Oil Temperature/Level Sensor harness connector pin 2 and a good ground. If continuity exists, repair the short to ground in the signal line circuit. If there is NO continuity, check the pins or the EMS Module for dirt, loose pins or deformed contacts. Replace the EMS Module if the pins of the module are not damaged. Retest the system.
4) Disconnect the Engine Oil Temperature/Level Sensor connector. Measure the resistance across the pins 1 and 2 of the Engine Oil Temperature/Level Sensor. With the engine at room temperature the sensor resistance should be 10.8-17.4 ohms. If the resistance of the sensor is NOT as specified, replace the Engine Oil Temperature/Level Sensor.
5) Disconnect the Engine Oil Temperature/Level Sensor harness connector. Disconnect the EMS Module harness connector B. Turn the ignition key ON. Measure voltage between Engine Oil Temperature/Level Sensor harness
connector pin 2 and a good ground. If the there is voltage present, repair the short to voltage on the signal line.
6) Disconnect the Engine Oil Temperature/Level Sensor connector. Disconnect connector B from the EMS Module. Check for continuity between connector B pin 4 of the EMS Module harness connector and pin 2 of the Engine Oil Temperature/Level Sensor harness connector. If there is NO continuity, locate and repair the circuit between the sensor and the EMS Module.
7) Disconnect the Engine Oil Temperature/Level Sensor connector. Disconnect connector B from the EMS Module. Check for continuity between connector B pin 3 of the EMS Module harness connector and pin 1 of the Engine Oil Temperature/Level Sensor harness connector. If there is NO continuity, locate and repair the circuit between the sensor and the EMS Module.
8) Visually inspect the EMS Module harness connectors A and B for dirt, loose pins or deformed contacts. If a repairable open is found or either of the pins feels loose, repair the EMS Module harness connector.
If the EMS Module harness connector is OK, verify the diagnostic code and the FMI, and retest. If FMI 5 is still active, replace the Engine Management System (EMS) Module and retest the system.
Related
-
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5
-
10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C
CAT $110.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5 -
Volvo Impact 2021 Trucks & Buses 06.2021 DVD 9116 Spare Parts Catalog
Trucks software $55.00Rated 0 out of 5 -
premium volvo tech tool update 2.8.150 diagnostic software 1pc
Trucks software $150.00Rated 0 out of 5 -
CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )
CAT $65.00Rated 0 out of 5 -
Detroit Diesel Diagnostic Link DDDL 8.0 PRO PROFESSIONAL Software trucks
Detroit $25.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1892 Throttle Position Sensor Pulse Width Modulation (PWM) Signal High Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines VT275 (2004 & Older)
INTERNATIONAL ENGINES $21.00Rated 0 out of 5