Volvo All Engines (2004 Emissions) Fault Code: PID 26 FMI 8 Fan Speed
Fault Condition: High engine coolant temperature could occur and cause engine shutdown.
If fault code PID 26 is set with FMI 3, fault code SID 211 may also be set.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between electronic fan drive harness connector pin 5 and a good ground.
If continuity exists, locate and repair the short circuit to ground in the supply voltage circuit between the electronic fan drive and the EMS Module.
2) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Turn the ignition key ON. Measure the voltage between electronic fan drive harness connector pin 5 and a good ground.
If voltage is present, locate and repair the short circuit to voltage in the supply voltage circuit between the electronic fan drive and the EMS Module.
3) Disconnect the electronic fan drive harness connector. Check for continuity between the sensor side of electronic fan drive connector pin 5 and a good ground. If continuity exists, replace the electronic fan drive assembly.
4) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Turn the ignition key ON. Measure the voltage between electronic fan drive harness connector pin 1 and a good ground.
If voltage is present, locate and repair the short circuit to voltage in the sensor signal circuit between the electronic fan drive and the EMS Module.
5) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between electronic fan drive harness connector pin 1 and a good ground.
If continuity exists, locate and repair the short circuit in the electronic fan drive signal line.
6) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between EMS Module harness connector A pin 39 and electronic fan drive harness connector pin 2.
If there is NO continuity, locate and repair the open circuit in the electronic fan drive ground line.
7) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between the sensor side of electronic fan drive connector pin 1 and a good ground (see Figure 14).
If continuity exists, replace the electronic fan drive assembly.
8) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between EMS Module harness connector A pin 7 and electronic fan drive harness connector pin 5.
If there is NO continuity, locate and repair the open circuit in the electronic fan drive supply line.
9) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between EMS Module harness connector A pin 35 and electronic fan drive harness connector pin 1.
If there is NO continuity, locate and repair the open circuit in the electronic fan drive signal line.
10) Disconnect EMS Module connector A. Visually inspect the EMS Module and connector A for broken, damaged, or shorted pins. If any damage is found, repair or replace the damaged component.
11) Replace the electronic fan drive with a known good unit. Restore all electrical connections an retest the system. If blink code PID 26 is still active, install the original electronic fan drive and replace the EMS Module.
If blink code PID 26 is NOT active, replacing the electronic fan drive solved the problem. Check all connectors to ensure proper connections.
Related
-
DOWNLOAD Paccar ESA Electronic Service Analyst 5.5.0 Diagnostic Software 2023
PACCAR $96.00Rated 0 out of 5 -
JPRO 2022 v1 Commercial Vehicle Diagnostics V1 Software Download & Installation Service ( 1 PC )
JPRO $94.00Rated 0 out of 5 -
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2
Trucks software $35.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 1.1.19.1 with keygen unlocked ( Hino trucks )
Hino $50.00Rated 0 out of 5 -
download MANCATS II v14.01 2014 Diagnostic software MAN CATS ( virtual machine )
MAN $75.00Rated 0 out of 5 -
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5 -
CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT $45.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5