Volvo All Engines (2004 Emissions) Fault Code: PID 26 FMI 8 Fan Speed
Fault Condition: High engine coolant temperature could occur and cause engine shutdown.
If fault code PID 26 is set with FMI 3, fault code SID 211 may also be set.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between electronic fan drive harness connector pin 5 and a good ground.
If continuity exists, locate and repair the short circuit to ground in the supply voltage circuit between the electronic fan drive and the EMS Module.
2) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Turn the ignition key ON. Measure the voltage between electronic fan drive harness connector pin 5 and a good ground.
If voltage is present, locate and repair the short circuit to voltage in the supply voltage circuit between the electronic fan drive and the EMS Module.
3) Disconnect the electronic fan drive harness connector. Check for continuity between the sensor side of electronic fan drive connector pin 5 and a good ground. If continuity exists, replace the electronic fan drive assembly.
4) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Turn the ignition key ON. Measure the voltage between electronic fan drive harness connector pin 1 and a good ground.
If voltage is present, locate and repair the short circuit to voltage in the sensor signal circuit between the electronic fan drive and the EMS Module.
5) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between electronic fan drive harness connector pin 1 and a good ground.
If continuity exists, locate and repair the short circuit in the electronic fan drive signal line.
6) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between EMS Module harness connector A pin 39 and electronic fan drive harness connector pin 2.
If there is NO continuity, locate and repair the open circuit in the electronic fan drive ground line.
7) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between the sensor side of electronic fan drive connector pin 1 and a good ground (see Figure 14).
If continuity exists, replace the electronic fan drive assembly.
8) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between EMS Module harness connector A pin 7 and electronic fan drive harness connector pin 5.
If there is NO continuity, locate and repair the open circuit in the electronic fan drive supply line.
9) Disconnect EMS Module connector A. Disconnect the electronic fan drive harness connector. Check for continuity between EMS Module harness connector A pin 35 and electronic fan drive harness connector pin 1.
If there is NO continuity, locate and repair the open circuit in the electronic fan drive signal line.
10) Disconnect EMS Module connector A. Visually inspect the EMS Module and connector A for broken, damaged, or shorted pins. If any damage is found, repair or replace the damaged component.
11) Replace the electronic fan drive with a known good unit. Restore all electrical connections an retest the system. If blink code PID 26 is still active, install the original electronic fan drive and replace the EMS Module.
If blink code PID 26 is NOT active, replacing the electronic fan drive solved the problem. Check all connectors to ensure proper connections.
Related
-
DAF Davie Runtime v5.6.1 Davie XDc ll [02.2019] + Expire Fix 302.00 Unlock ( Windows 7 )
DAF $70.00Rated 0 out of 5 -
Bobcat Service Library [03.2019] Service, Operator, Maintenance, Bulletines, etc full update
Bobcat $110.00Rated 0 out of 5 -
DPF EGR SCR BAC ERG Delete & Flash CAAT Cummings Detroit Dodge Mack Volvo Collection of DELETE files
CAT $200.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5