Volvo Engine D13F Fault Code: PPID 123 FMI 5 EPG 2 Start and Warmhold

Related products

• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 731 PID: SID 064 SPN: 723 FMI: 7 Engine Speed/Position Camshaft and Crankshaft Misalignment – Mechanical System Not Responding Properly or Out of Adjustment. Engine position signal from the engine speed sensor and camshaft position sensor do not match.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 731 PID: SID 064 SPN: 723 FMI: 7 Engine Speed/Position Camshaft and Crankshaft Misalignment – Mechanical System Not Responding Properly or Out of Adjustment. Engine position signal from the engine speed sensor and camshaft position sensor do not match.

  Cumminz

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 2635 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Condition Exists. A calibration mismatch between the VGT actuator and the ECM has been detected.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 432 PID: SID 230 SPN: 558 FMI: 13 Accelerator Pedal or Lever Idle Validation Circuit – Out of Calibration. Voltage at idle validation on-idle and off-idle circuit does not match accelerator pedal position.

  Cumminz

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 2198 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Root Cause Not Known. Intermittent communication between the smart VGT controller and the ECM has been detected. The VGT controller is not interpreting the J1939 message from the ECM correctly.

  DTC TRUCKS

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 1242 PID: 91 SPN: 91 FMI: 2 Accelerator Pedal or Lever Position Sensor 1 and 2 – Data Erratic, Intermittent, or Incorrect. Accelerator position sensor number 1 and number 2 are reading different values.

  DTC TRUCKS

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 649 PID: SID 115 SPN: 1378 FMI: 11 Engine Oil Change Interval – Condition Exists. Change engine oil and filter.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 649 PID: SID 115 SPN: 1378 FMI: 11 Engine Oil Change Interval – Condition Exists. Change engine oil and filter.

  Cumminz

  Rated 0 out of 5
• 

  PACCAR PX-8 CM2150 (2007-09) Fault Code: 2635 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Condition Exists. A calibration mismatch between the VGT actuator and the ECM has been detected.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Allison 1000 and 2000 Series Gen 4 (2005-11) Service manual

  Allison $10.00

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2198 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Root Cause Not Known. Intermittent communication between the smart VGT controller and the ECM has been detected.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 1663 PID: None SPN: 3241 FMI: 11 Catalyst Inlet Temperature Sensor Swapped with Outlet – Condition Exists. The inlet and outlet catalyst temperature sensor connections are swapped.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 1242 PID: 91 SPN: 91 FMI: 2 Accelerator Pedal or Lever Position Sensor 1 and 2 – Data Erratic, Intermittent, or Incorrect.

  Cumminz

  Rated 0 out of 5
• 

  PACCAR PX-8 CM2150 (2007-09) Fault Code: 2754 PID: SPN: 81 FMI: 16 Engine Particulate Filter Inlet Pressure – Data Valid but Above Normal Operational Range – Moderately Severe Level. Excessive black smoke has been detected exiting the engine and entering the aftertreatment diesel particulate filter.

  DTC TRUCKS

  Rated 0 out of 5
• 

  PACCAR PX-8 CM2150 (2007-09) Fault Code: 2636 PID: SID 027 SPN: 641 FMI: 9 VGT Actuator Driver Circuit – Abnormal Update Rate. No communications on the J1939 data link between the engine ECM and the smart VGT controller.

  DTC TRUCKS

  Rated 0 out of 5