Voltage from the Engine Control Module (ECM) is applied to the Water In Fuel Filter Sensor when the ignition switch is in the ON position. If water is detected, the Water In Fuel Filter sensor will notify the driver to drain the water from the bowl by illuminating a lamp on the dash of the vehicle.

Conditions for diagnostic trouble code (DTC):
1) The voltage at pin A14.EB:8 is less than 1.2?V

Observable symptoms
1) Water in the fuel can lead to engine failure

Probable cause
1) Faulty sensor
2) Wiring harness
3) Connector

Reviews

There are no reviews yet.

Be the first to review “Volvo All Engines (2010 Emissions) Fault Code: SPN 97 FMI 5 PID: Water in Fuel Indicator”

Volvo All Engines (2010 Emissions) Fault Code: SPN 97 FMI 5 PID: Water in Fuel Indicator

Related

Reviews

Cumminmms Insiter 8.9 Diagnostic Software

JPRO Diagnostic Software Download 2024

AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125

DOOSAN DMS-5 3.1.3 [2023.11] diagnostic software 1PC

DDDL 8.17 2023 Detroit Diesel Diagnostic Link Software

John Deere Service Advisor 5.3 CF & AG 2020.08

JPRO 2022 v3 ( 1 PC )

Perkins EST 2022A ( 1 PC )

Cumminmms Insiter 8.9 Diagnostic Software

CAT SIS caterpillar 2021 Full Service Dealer

NAVISTAR ENGINE CYLINDER PERFORMANCE ANALYZER V7.8.8.1

JPRO Diagnostic Software Download 2024

10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C

VOLVO PREMIUM TECH TOOL PTT 2.7.116 + APCI 2021 + devtool ( ONLINE )

volvo delete files 2023 33,46 GB

DAF Davie Runtime v5.6.1 Davie XDc ll [02.2019] + Expire Fix 302.00 Unlock ( Windows 7 )

Isuzu IDSS 2021 Diagnostic Software

Allison doc premium update 2023 v1 Diagnostic Software Download

Bobcat Service Library [03.2019] Service, Operator, Maintenance, Bulletines, etc full update

Related products

Allison 1000 & 2000 Gen 5 Fault Code:P1790 Gear Shift Module 1 Calibration Invalid

Allison 1000 & 2000 Gen 5 Fault Code:P2669 Actuator Supply Voltage 2 Open

Allison 1000 & 2000 Gen 5 Fault Code:P0973 Shift Solenoid 1 (SS1) Control Circuit – Low

Allison 1000 & 2000 Gen 5 Fault Code:P2729 Pressure Control Solenoid 1 (PCS1) Control Circuit – Low

Allison 1000 & 2000 Gen 5 Fault Code:P2724 Pressure Control Solenoid 1 (PCS1) – Stuck On

Allison 1000 & 2000 Gen 5 Fault Code:P2684 Actuator Supply Circuit Voltage 3 Open (HSD3)

Allison 1000 & 2000 Gen 5 Fault Code:P2670 Actuator Supply Voltage 2 (HSD2) – Low

Allison 1000 & 2000 Gen 5 Fault Code:P2685 Actuator Supply Circuit Voltage 3 Low (HSD3)

Allison 1000 & 2000 Gen 5 Fault Code:P0979 Shift Solenoid 3 (SS3) Control Circuit – Low

Allison 1000 & 2000 Gen 5 Fault Code:P2637 Torque Management Feedback Signal – SEM

Allison 1000 & 2000 Gen 5 Fault Code:P2764 TCC PCS Control Circuit Low

Allison 1000 & 2000 Gen 5 Fault Code:P2727 Pressure Control Solenoid 1 (PCS1) Control Circuit – Open

Cummins ISM CM875 (2003-06) Fault Code: 585 PID: S39 SPN: 677 FMI: 4/4 Starter Relay Driver Circuit – Voltage Below Normal or Shorted to Low Source. Low voltage detected at starter lockout circuit.

Detroit DD15 EPA07 (2007-09) Fault Code: SPN 3610 FMI 20 (MCM) Diesel Particulate Filter Outlet Pressure Sensor Fault

Detroit DD15 EPA07 (2007-09) Fault Code: SPN 3246 FMI 16 (MCM) Diesel Particulate Filter Outlet Temperature – High

Detroit DD13 EPA07 (2007-09) Fault Code: SPN 1077 FMI 31 (MCM) Fuel Rail Pressure Deviation is Greater than 200 Bar for Eight Seconds

Cummins ISC CM2150 (2007-09) Fault Code: 2186 PID: SID 232 SPN: 3512 FMI: 4 Sensor Supply 4 Circuit – Voltage Below Normal or Shorted to Low Source. Low voltage detected at the +5 volt sensor supply circuit to the accelerator pedal position sensor.

Cummins ISB4.5 CM2150 Fault Code: 346 PID: 253 SPN: 630 FMI: 12 Engine Control Module Calibration Memory Software – Bad Intelligent Device or Component.

PACCAR PX-8 CM2150 (2007-09) Fault Code: 1966 PID: 326 SPN: 3241 FMI: 0 Aftertreatment Exhaust Gas Temperature 1 – Data Valid But Above Normal Operating Range – Most Severe Level. Engine exhaust gas temperatures entering the aftertreatment system are above the engine protection limits.

PACCAR PX-9 CM2350 (2013-17) Fault Code:3139 PID: SPN:3667 FMI:3 Engine Air Shutoff Circuit – Voltage Above Normal or Shorted to High Source

PACCAR MX (2004 Emissions) Fault Code: P0272 Cylinder 4 – Torque Contribution Too Low

Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 242 PID: PID 84 SPN: 84 FMI: 10 Wheel-Based Vehicle Speed Sensor Circuit Tampering Has Been Detected- Abnormal Rate of Change

Detroit DD13 EPA10 (2010-13) Fault Code: SPN 94 FMI 4 (MCM) Low Side Fuel Pressure Sensor Circuit Failed Low

Detroit DD15 EPA07 (2007-09) Fault Code: SPN 1636 FMI 20 (MCM) Intake Manifold Temperature Drift (Low Box)

Detroit DD13 GHG14 (2014-16) Fault Code: SPN 91 FMI 31 (CPC) 2- Channel Accelerator Pedal Learned Range to Large

Detroit DD13 GHG14 (2014-16) Fault Code: SPN 1073 FMI 5 (MCM) Jake Brake Stage 2 Circuit Failed Open

Cummins ISX15 CM2250 (2010-12) Fault Code: 427 PID: SID 231 SPN: 639 FMI: 9 SAE J1939 Data Link- Abnormal Update Rate

Cummins X12 CM2350 X119B (2018 & Newer) Fault Code: 4677 PID: SPN: 1761 FMI: 9 Aftertreatment 1 Diesel Exhaust Fluid Tank Level- Abnormal Update Rate

Cummins ISB CM850 (2003-06) Fault Code: 551 (ISS) PID: SID 230 SPN: 558 FMI: 4 Accelerator Pedal or Lever Idle Validation Circuit – Voltage Below Normal or Shorted to Low Source. No voltage detected simultaneously on both the idle validation and off-idle and on-idle switches.

PACCAR PX-9 CM2350 (2013-17) Fault Code:3146 PID: SPN:4363 FMI:3 Aftertreatment 1 SCR Outlet Temperature Sensor Circuit – Voltage Above Normal or Shorted to High Source

Store

About

Features

Follow Us