Voltage from the Engine Control Module (ECM) is applied to the Water In Fuel Filter Sensor when the ignition switch is in the ON position. If water is detected, the Water In Fuel Filter sensor will notify the driver to drain the water from the bowl by illuminating a lamp on the dash of the vehicle.

Conditions for diagnostic trouble code (DTC):
1) Short circuit to battery voltage on A14.EB:8

Observable symptoms
1) Indicator does not work
2) Water in the fuel can lead to engine failure
3) Low Power

Probable cause
1) Faulty sensor
2) Short circuit to voltage supply, signal wire
3) Connector
4) Engine control module (ECM)

Reviews

There are no reviews yet.

Be the first to review “Volvo All Engines (2010 Emissions) Fault Code: SPN 97 FMI 3 PID: Water in Fuel Indicator”

Volvo All Engines (2010 Emissions) Fault Code: SPN 97 FMI 3 PID: Water in Fuel Indicator

Related

Reviews

Cumminmms Insiter 8.9 Diagnostic Software

JPRO Diagnostic Software Download 2024

AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125

DOOSAN DMS-5 3.1.3 [2023.11] diagnostic software 1PC

CATERPILLAR FLASH FILE 2021 74 GB ( Collection 2021 ) sofware trucks

Download Renault Trucks NG3 NG10 calculator v0.1

Perkins EST 2022A ( 1 PC )

DOWNLOAD Paccar ESA Electronic Service Analyst 5.5.0 Diagnostic Software 2023

VOLVO PREMIUM TECH TOOL PTT 2.7.116 + APCI 2021 + devtool ( ONLINE )

Freightliner ServiceLink 4.9.6

CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language

CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10

DPF EGR SCR BAC ERG Delete & Flash CAAT Cummings Detroit Dodge Mack Volvo Collection of DELETE files

JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023

Detroit Diagnostic Link (DDDL 8.09) Engineering level 10

Caterpillar ET 2022A Electronic Technician + Factory Password (1PC)

Diamond Logic Builder DLB 2018

VOLVO IMPACT 2022 V.9227 offline

Bobcat Software Service Analyzer Version 87.07 ( 1PC )

Related products

Allison 1000 & 2000 Gen 5 Fault Code:P2729 Pressure Control Solenoid 1 (PCS1) Control Circuit – Low

Allison 1000 & 2000 Gen 5 Fault Code:P1790 Gear Shift Module 1 Calibration Invalid

Allison 1000 & 2000 Gen 5 Fault Code:P0973 Shift Solenoid 1 (SS1) Control Circuit – Low

Allison 1000 & 2000 Gen 5 Fault Code:P2669 Actuator Supply Voltage 2 Open

Allison 1000 & 2000 Gen 5 Fault Code:P2684 Actuator Supply Circuit Voltage 3 Open (HSD3)

Allison 1000 & 2000 Gen 5 Fault Code:P0980 Shift Solenoid 3 (SS3) Control Circuit – High

Allison 1000 & 2000 Gen 5 Fault Code:P2789 Clutch Adaptive Learning at Limit

Allison 1000 & 2000 Gen 5 Fault Code:P0122 Pedal Position Sensor Circuit – Low Voltage

Allison 1000 & 2000 Gen 5 Fault Code:U0073 CAN Communication Bus 1 Off

Allison 1000 & 2000 Gen 5 Fault Code:P0979 Shift Solenoid 3 (SS3) Control Circuit – Low

Allison 1000 & 2000 Gen 5 Fault Code:P2730 Pressure Control Solenoid 1 (PCS1) Control Circuit – High

Allison 1000 & 2000 Gen 5 Fault Code:P2641 Torque Management Feedback Signal – LRTP

Cummins ISX12 CM2250 (2010-12) Fault Code: 256 PID: 171 SPN: 171 FMI: 4 Ambient Air Temperature Sensor 1 Circuit- Voltage Below Normal or Shorted to Low Source

Cummins ISX11.9 CM2250 (2010-12) Fault Code: 5383 (BCL) PID: SPN: 3720 FMI: 15 Aftertreatment 1 Diesel Particulate Filter Ash Load Percent- Data Valid But Above Normal Operating Range- Least Severe Level

Detroit DD16 GHG14 (2014-16) Fault Code: SPN 100 FMI 10 (MCM) Low Oil Pressure Derate

Allison WTEC II Fault Code: 54 PID: SPN: 53 FMI: Oncoming ratio test (during shift), 5 to 3

Cummins ISX CM870 (2003-06) Fault Code: 286 PID: S231 SPN: 639 FMI: 13/13 The ECM expected information from a multiplexed device but only received a portion of the necessary information.

PACCAR PX-8 CM2150 (2007-09) Fault Code: 2778 PID: 289 SPN: 3481 FMI: 0 Aftertreatment Fuel Rate – Data Valid but Above Normal Operational Range – Moderately Severe Level. The lubricating engine oil needs to be changed due to possible fuel dilution.

CAT 3126B Fault Code: 41-04 PID: Flash Code 21 SPN: 678 FMI: 4 8 Volt Supply Below Normal

Volvo All Engines (2013 Emissions) Fault Code: P20DD12 PID: EMS Exhaust Aftertreatment Fuel Pressure Sensor

Cummins ISL CM850 (2003-06) Fault Code: 352 PID: SID 212 SPN: 1079 FMI: 4 Sensor Supply Voltage Number 1 Circuit – Voltage Below Normal or Shorted to Low Source. Low voltage detected at sensor supply number 1 circuit.

Detroit DD16 GHG14 (2014-16) Fault Code: SPN 3845 FMI 3 (CPC) Digital Input 1 12 – Failed High on Pin 12 Circuit of the Common Powertrain Controller #1 Connector

Detroit DD16 GHG14 (2014-16) Fault Code: SPN 3716 FMI 31 (ACM) High Idle Regeneration Aborted – Low Coolant Temp

Detroit DD13 EPA10 (2010-13) Fault Code: SPN 652 FMI 4 (MCM) Injector Cylinder #2 Needle Control Valve Abnormal Operation (MIN)

Volvo All Engines (2017 Emissions) Fault Code: P229E64 PID: EMS NOx Sensor Bank 1 Sensor 2

Detroit DD15 EPA10 (2010-13) Fault Code: SPN 600 FMI 13 (CPC) J1939 Cruise Coast Switch Signal from Source #1, #2 Or #3 is Missing

Cummins ISX12 CM2250 (2010-12) Fault Code: 1664 PID: SID 380 SPN: 4796 FMI: 31 Aftertreatment Diesel Oxidation Catalyst Missing- Condition Exists

Cummins ISL CM850 (2003-06) Fault Code: 1142 PID: SID 3 SPN: 653 FMI: 7 Injector Solenoid Driver Cylinder 3 – Mechanical System Not Responding Properly or Out of Adjustment. Unintended fueling detected in cylinder number 3.

Detroit DD16 GHG14 (2014-16) Fault Code: SPN 51 FMI 18 (MCM) Intake Throttle Position Rationality Error

Cummins X12 CM2350 X119B (2018 & Newer) Fault Code: 5793 PID: SPN: 7323 FMI: 3 Aftertreatment 1 Particulate Sensor Heater Low Side Driver Circuit- Voltage Above Normal or Shorted to High Source

Store

About

Features

Follow Us