Volvo All Engines (2004 Emissions) Fault Code: SID 33 FMI 4 Cooling Fan Control
Fault Condition: When the Engine Management System (EMS) Module detects there is a short to voltage in the cooling fan control circuit. When there is a short to ground, FMI 4 will set and the fan will not operate
Note: If code SID 33 sets with FMI 4, there may be additional active codes. If this is the case, follow the diagnostic procedures for the other codes first, then check to make sure code SID 33 is no longer active.
If a customer complains that the fan clutch does not disengage and code SID 33 has not been logged in the EMS Module, the problem may be due to a mechanical failure in the chassis air system.
Possible repairs:
Warning: The fan can engage without warning. Hands, arms and personal items can easily be entangled in the belts or fan blades. Keep arms, hair, clothing, jewelry, etc. clear from the fan and belts when the engine is running.
Turn the ignition key OFF first.
1) Disconnect connector from the Fan Clutch Solenoid connector and the Engine Management System (EMS) Module connector B. Check for continuity between the Fan Clutch Solenoid harness connector pin 3 and a good ground. If continuity exists to ground, locate and repair the short circuit to ground. If there is NO continuity, replace the Fan Clutch Solenoid and retest the system. If the FMI 4 is still active after replacing the solenoid, verify the diagnostic code, the FMI and retest the system. If the FMI 4 is still active, replace the EMS Module and retest the system.
2) Disconnect connector from the Fan Clutch Solenoid. Turn the ignition key ON. Measure the voltage between Fan Clutch Solenoid connector pin 4 and a good ground. If 12 volts is not present, then there is an open or short in the voltage circuit to the solenoid. Locate and repair the open or short circuit.
3) Disconnect the connector from the Fan Clutch Solenoid. Check for continuity between the Fan Clutch Solenoid pins 3 and 4. If there is NO continuity, replace the Fan Clutch Solenoid and retest the system.
4) Disconnect connector from the Fan Clutch Solenoid connector and the Engine Management System (EMS) Module connector B. Check for continuity between the Fan Clutch Solenoid harness connector pin 3 and the
EMS Module harness connector B pin 49. If there is NO continuity, locate and repair the open in the circuit.
5) Disconnect EMS Module connector B. Visually inspect EMS Module connector B for dirt, loose pins or deformed contacts. If a repairable open is found or the terminal feels loose, repair the harness connector.
If the test lead is making good contact with the connector terminal, verify the diagnostic code, the FMI and retest the system. If the FMI 5 is still active, replace the EMS Module and retest the system.
Related
-
International Truck ISIS – Oncommand Service Information Q4.2020 [04.2020]
Navistar $85.00Rated 0 out of 5
-
PACCAR Electronic Service Analyst 5.4.3.0 SW files 27.03.2021 software trucks
PACCAR $60.00Rated 0 out of 5 -
PF Diagnose 2.0.2.23 Diagnostics Software 2013 – Full Heavy & Medium Duty with OBDII Support – Online Installation Service
PF Diagnose $60.00Rated 0 out of 5 -
download Hitachi Construction Machinery MPDr Ver 3.7.0.0 [10.2020] Diagnostic Software
Hitachi $76.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1892 Throttle Position Sensor Pulse Width Modulation (PWM) Signal High Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL DETROIT DIESEL EPA 07, EPA 10, GHG 14 TROUBLESHOOTING
DETROIT $38.00Rated 0 out of 5