Volvo All Engines (2004 Emissions) Fault Code: SID 231 FMI 2 CAN1 J1939 Communication Link A
Fault Condition: Code SID 231 will set when the Vehicle Electronic Control Unit (VECU) is unable to send and/or receive information across the J1939 data line. If either the Vehicle Electronic Control Unit (VECU) or the Engine
Management System (EMS) Module loses communication on the J1939 data line, code SID 231 will set and the Electronic Malfunction Lamp (EML) will turn on. The fault will become inactive if communication resumes. If communication is lost on both the J1587 and J1939 data lines the engine will NOT run.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect the Vehicle Electronic Control Unit (VECU) connectors A, B and C. Check for continuity between Vehicle Electronic Control Unit (VECU) connector C pin 4 and all other pins (except Vehicle Electronic Control Unit (VECU) connector C pin 5) on connectors A, B and C. Then check for continuity between Vehicle Electronic Control Unit (VECU) connector C pin 5 and all other pins (except Vehicle Electronic Control Unit (VECU) connector C pin 4) on connectors A, B and C. If continuity exists, repair or replace the damaged data line harness or connectors. If continuity does not exist, replace the Vehicle Electronic Control Unit (VECU).
2) Disconnect the Vehicle Electronic Control Unit (VECU) connector C. Check for continuity between Vehicle Electronic Control Unit (VECU) connector C pin 5 and pin D of the Data Link Connector (DLC). Then check for continuity between Vehicle Electronic Control Unit (VECU) connector C pin 4 and pin C of the Data Link Connector (DLC). If the continuity exists, replace the Vehicle Electronic Control Unit (VECU). If the continuity does not exists, locate and repair the open in the data line and retest the system.
3) Disconnect the CAN-BUS Termination Resistor connector. Check for continuity between pins 1 and 2 of the CAN-BUS Termination Resistor. If the resistance is NOT between 115–125 Ohms, replace the CAN-BUS Termination
Resistor.
4) Disconnect the Vehicle Electronic Control Unit (VECU) connector C. Check the resistance between the Vehicle Electronic Control Unit (VECU) connector C pins 4 and 5 on the VECU side. If continuity is between 115–125 Ohms, locate and repair an open in the data line. If continuity is NOT between 115–125 Ohms, check the Vehicle Electronic Control Unit (VECU) harness and all connections for loose, corroded or damaged terminals and repair or replace as necessary. If no loose, corroded or damaged terminals are found, replace the Vehicle Electronic Control Unit (VECU).
Related
-
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5 -
DAF Davie Runtime v5.6.1 Davie XDc ll [02.2019] + Expire Fix 302.00 Unlock ( Windows 7 )
DAF $70.00Rated 0 out of 5
-
2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )
Trucks software $85.00Rated 0 out of 5 -
Volvo Premium Tech Tool PTT 2.8.130 Diagnostic Software 04.2022 ACPI ( 1 PC )
Trucks software $143.00Rated 0 out of 5 -
CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )
CAT $65.00Rated 0 out of 5 -
Detroit Diesel Diagnostic Link DDDL 8.0 PRO PROFESSIONAL Software trucks
Detroit $25.00Rated 0 out of 5 -
Bobcat Service Library [03.2019] Service, Operator, Maintenance, Bulletines, etc full update
Bobcat $110.00Rated 0 out of 5 -
download Hitachi Construction Machinery MPDr Ver 3.7.0.0 [10.2020] Diagnostic Software
Hitachi $76.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1892 Throttle Position Sensor Pulse Width Modulation (PWM) Signal High Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5