Volvo All Engines (2004 Emissions) Fault Code: SID 230 FMI 5 Idle Validation Switch
Fault Condition: A fault of FMI 3 will be logged if the IVS voltage is greater than 8.5 volts and the pedal position less than 1%. If the voltage is approximately 0 volts and the pedal position is greater than 50%, an FMI 5 will set.
Possible repairs:
Turn the ignition key OFF first.
1) If code SID 230 is not set, wiggle the harness and connectors to try to set the code. Visually inspect the VECU connectors and wires for poor connections.
2) Disconnect connector B from the Engine Management System (EMS) Module. Disconnect connector B from the Vehicle Electronic Control Unit (VECU). Turn the ignition key ON. Check for voltage at harness connector B
pin 15 of the EMS Module harness and a good ground. The measured voltage should be 0 volts. If there is voltage indicated, repair the short to power in the harness and retest the system. If there is NO voltage indicated, verify the diagnostic code, the FMI and retest the system. If the FMI 3 is still active, replace the EMS Module and retest the system.
3) Disconnect connector B from the Engine Management System (EMS) Module. Disconnect connector B from the Vehicle Electronic Control Unit (VECU). Check for continuity between harness connector B pin 15 of the EMS Module harness and harness connector B pin 17 of the Vehicle Electronic Control Unit (VECU) If there is NO continuity, repair the open in the harness and retest the system.
4) Disconnect connector B from the Engine Management System (EMS) Module. Disconnect connector B from the Vehicle Electronic Control Unit (VECU). Check for continuity between harness connector B pin 15 of the EMS Module harness and a good ground. If there is continuity, repair the short to ground in the harness and retest the system.
5) Disconnect EMS Module connector B. Visually inspect EMS Module connector B for dirt, loose pins or deformed contacts. If a repairable open is found or the terminal feels loose, repair the harness connector. If the test lead is making good contact with the connector terminal, verify the diagnostic code, the FMI and retest the system. If the FMI 5 is still active, replace the EMS Module and retest the system.
Related
-
PACCAR Electronic Service Analyst 5.4.3.0 SW files 27.03.2021 software trucks
PACCAR $60.00Rated 0 out of 5 -
CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )
CAT $65.00Rated 0 out of 5 -
Detroit Diesel Diagnostic Link DDDL 8.0 PRO PROFESSIONAL Software trucks
Detroit $25.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines DT466 (2004-2006)
INTERNATIONAL ENGINES $45.00Rated 0 out of 5