Volvo All Engines (2004 Emissions) Fault Code: SID 211 FMI 3 Sensor Supply Voltage #2
Fault Condition: The Electronic Malfunction Lamp (EML) will turn on and code SID 211 will set when the reference voltage to the Fuel Pressure Sensor, Crankcase Pressure Sensor and the Oil Pressure Sensor is less than 4.5 volts or greater than 5.5 volts. If the voltage returns to 4.5 volts to 5.5 volts, the fault will become inactive.
Possible repairs:
Turn the ignition key OFF first.
1) Check if code SID 211 is set. Check if any other code is also set. If any other code code is set, go to the diagnostic routine for the specific code. If code SID 211 is NOT set, wiggle the harness and connectors to try to set the
code. Visually inspect the EMS Module connectors for frayed wires and loose or corroded connections.
2) Disconnect EMS Module connector B. Disconnect the Fuel Pressure Sensor, Crankcase Pressure Sensor and the Oil Pressure Sensor harness connectors. Check for continuity between EMS Module harness connector B, pin 17 and a good ground. If continuity exists, locate and repair the short circuit to ground.
3) Disconnect EMS Module connector B. Turn the ignition key ON. Measure the voltage between EMS Module connector B pin 17 and a good ground. If voltage is present, locate and repair the short circuit to voltage in circuit.
4) Disconnect EMS Module connector B. Disconnect the Fuel Pressure Sensor, Crankcase Pressure Sensor and the Oil Pressure Sensor harness connectors. Check for continuity between EMS Module harness connector B, pin 17 and a pin 1 of the Fuel Pressure Sensor, Crankcase Pressure Sensor and the Oil Pressure Sensor connectors. If there is NO continuity, locate and repair the open in the circuit.
5) Disconnect EMS Module connector B. Visually inspect both sides of EMS Module connector B. If a repairable short circuit or damaged pins are found, repair or replace the harness connector.
6) Connect EMS Module connector B. Connect the Fuel Pressure Sensor, Crankcase Pressure Sensor and the Oil Pressure Sensor harness connectors. Start the engine. If code SID 211 is still active, replace the EMS Module and retest the system. If code SID 211 is not active, the diagnostic procedures have corrected the problem. Check all connectors to ensure proper connections.
Related
-
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5 -
download MANCATS II v14.01 2014 Diagnostic software MAN CATS ( virtual machine )
MAN $75.00Rated 0 out of 5
-
Navistar international OnCommand service information 2018 software trucks
Navistar $50.00Rated 0 out of 5 -
Eaton Service Ranger 4.9 Engineering 4.9 [05.2021] Engineering Level ( 1 PC )
Eaton $67.00Rated 0 out of 5 -
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2
Trucks software $35.00Rated 0 out of 5 -
Wabco ToolBox plus 13.7.0.1 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5 -
DETROIT DDDL 8.14 SP3 – Detroit Diesel Diagnostic Link 8.14 SP3 2021 ( 1PC )
Detroit $73.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce 7 (2007-2009)
INTERNATIONAL ENGINES $31.00Rated 0 out of 5 -
SERVICE MANUAL Eaton Fuller – Autoshift, Autoselect Service Manual (TRSM-0050)
EATON $25.00Rated 0 out of 5 -
SERVICE MANUAL International Engines DT466E & DT530E (1999 & Older)
INTERNATIONAL ENGINES $31.00Rated 0 out of 5 -
SERVICE MANUAL INTERNATIONAL ENGINE VT365 (2003 & Older)
INTERNATIONAL ENGINES $24.00Rated 0 out of 5