Volvo All Engines (2004 Emissions) Fault Code: SID 21 FMI 3 Cam Speed Sensor
Fault Condition: Management System (EMS) Module senses a significant difference between the engine speed calculated from the CAM Speed Sensor signal and the engine speed calculated from the Crank Speed Sensor, the EMS Module will turn on the Electronic Malfunction Light, and code SID 21 will set. If the signals return to normal, the code will become inactive. The engine must be running to set an active CAM Speed Sensor fault code.
Note: Electrical problems can cause this fault to be generated, and electrical diagnostics are provided in this section. Mechanical problems can also cause temporary or permanent speed signal errors. After all electrical possibilities have been ruled out, check mechanical conditions that could cause vibration or signal errors. Such conditions include but are not limited to:
Faulty Engine Vibration Damper, Contaminated sensor tips, Contaminated Cam Gear face, Excessive Camshaft end play, Improperly adjusted sensor, Improperly balanced engine components, Faulty engine timing cover.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect the CAM Speed Sensor. Measure the resistance between terminals 1 and 2 on the CAM Speed Sensor. If the resistance is not between 775–945 ohms check the CAM Speed Sensor pigtail connector and wiring for damage. If the connector and wiring are not damaged, replace the CAM Speed Sensor.
2) Disconnect the CAM Speed Sensor connector. Measure the resistance between sensor pin 1 and a good ground and between sensor pin 2 and a good ground. If continuity exists between either pin and ground, replace the sensor.
3) Disconnect connectors A and B from the EMS Module. Disconnect the CAM Speed Sensor connector. Check for continuity between EMS Module connector A pin 45 and all other pins on EMS Module connectors A and B.
If continuity exists, pin 45 is shorted to one of the other EMS Module circuits. Locate and repair the short circuit to voltage. If there is NO continuity, the sensor return line is shorted to voltage somewhere else in the harness. Locate and repair the short circuit to voltage.
4) Disconnect connectors A and B from the EMS Module. Disconnect the CAM Speed Sensor. Check for continuity between EMS Module connector A pin 46 and all other pins on EMS Module connectors A and B. If continuity exists between pin 46 and any other pin, pin 46 is shorted to one of the other EMS Module circuits. Locate and repair the short circuit to voltage. If there is NO continuity, the sensor return line is shorted to voltage somewhere else in the harness. Locate and repair the short circuit to voltage.
5) Disconnect the CAM Speed Sensor. Disconnect EMS Module connectors A and B. Check for continuity between EMS Module connector A pins 45 and 46 versus all other pins on EMS Module connectors A and B. If continuity exists, the suspect pin is shorted to one of the other EMS Module circuits. Locate and repair the short circuit.
6) Disconnect the CAM Speed Sensor. Disconnect EMS Module connectors A and B. Check for continuity between the circuit (connector A pin 45 or 46) that showed continuity in test 7, versus all other pins on EMS Module connectors A and B. If continuity exists, the suspect pin is shorted to one of the other EMS Module circuits. Locate and repair the short circuit. If there is NO continuity, the suspect circuit is shorted to ground somewhere else in the harness. Locate and repair the short circuit.
7) Connect the CAM Speed Sensor. Disconnect EMS Module connector A. Measure the resistance between EMS Module connector A pins 45 and 46. If the resistance is not within this range, the CAM Speed Sensor has an open circuit or a faulty connector. Repair the connector if possible, otherwise, replace the sensor.
8) Connect the CAM Speed Sensor connector. Connect EMS Module connectors A and B. Start the engine. If blink code SID 21 is still active, check the EMS Module and connectors for dirt, loose or broken pins, or repairable damage. If no problems are evident, or they are not repairable, replace the EMS Module and retest the system. If blink code SID 21 is NOT active, the diagnostic procedures have corrected the problem. Check all connectors to ensure proper connections.
Related
-
Volvo Impact 2021 Trucks & Buses 06.2021 DVD 9116 Spare Parts Catalog
Trucks software $55.00Rated 0 out of 5 -
John Deere & Hitachi Parts ADVISOR 2020 [08.2020] Offline DVD Spare Parts Catalog
John Deere $120.00Rated 0 out of 5
-
volvo Devtool Studio V2 / V3 / V4 Developer tool plus 2.6 / 2.7
Trucks software $35.00Rated 0 out of 5 -
Eaton Service Ranger 4.9 Engineering 4.9 [05.2021] Engineering Level ( 1 PC )
Eaton $67.00Rated 0 out of 5 -
JPRO 2022 v1 Commercial Vehicle Diagnostics V1 Software Download & Installation Service ( 1 PC )
JPRO $94.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
service manual TroubleshootingManual Allison TransmissionMD/HD/B -Series -TransmissionsWTEC II Controls
Allison $25.00Rated 0 out of 5 -
SERVICE MANUAL Carrie Supra 422, 522,622, 722, 822,922, 644,744,844, 944 & Supra Multi-Temp
CARRIE $20.00Rated 0 out of 5