Volvo All Engines (2004 Emissions) Fault Code: PSID 201 FMI 9 CAN1 J1939 Communication Link B
Fault Condition: Code PSID 201 will set when the Engine Management System (EMS) Module loses communication with the Vehicle Electronic Control Unit (VECU) on the J1939 data line. The fault will become inactive if communication resumes. If communication is lost on both the J1587 and J1939 data lines, the engine will still run using the idle validation switch.
Possible repairs:
1) If code PSID 201 is NOT set, wiggle the EMS Module and VECU harnesses and connectors to try to set the code. Visually inspect the EMS Module and VECU connectors and wires for poor connections.
2) Disconnect the Vehicle Electronic Control Unit (VECU) connector A. Turn the ignition key ON. Measure the voltage between Vehicle Electronic Control Unit (VECU) connector A pin 13 and a good ground. Then measure the voltage between Vehicle Electronic Control Unit (VECU) connector A pin 14 and a good ground. If the measured voltage is 0 volts, check the battery power circuit to the Vehicle Electronic Control Unit (VECU). If the measured voltage is NOT approximately battery voltage at either pin, check the battery power circuit and connectors for loose, corroded or damaged terminals and repair as necessary.
3) Disconnect the Vehicle Electronic Control Unit (VECU) connector A. Turn the ignition key ON. Disconnect the Vehicle Electronic Control Unit (VECU) connector A. Check for continuity between Vehicle Electronic Control Unit (VECU) connector A pin 12 and a good ground. If continuity does NOT exist, repair the open in the ground circuit.
4) Turn the ignition switch OFF. Disconnect the Engine Management System (EMS) Module connector B. Disconnect the Vehicle Electronic Control Unit (VECU) connector C. Check for continuity between Engine Management System (EMS) Module connector B pin 55 and Vehicle Electronic Control Unit (VECU) connector C pin 5. If continuity does NOT exist, locate and repair the open in the data line and retest the system.
5) Turn the ignition switch OFF. Disconnect the Engine Management System (EMS) Module connector B. Disconnect the Vehicle Electronic Control Unit (VECU) connector C. Check for continuity between Engine Management System (EMS) Module connector B pin 51 and Vehicle Electronic Control Unit (VECU) connector C pin 4. If continuity exists, check the Engine Management System (EMS) Module harness and all connections for loose,
corroded or damaged terminals and repair or replace as necessary. If no loose, corroded or damaged terminals are found, replace the Engine Management System (EMS) Module.
If continuity does not exists, locate and repair the open in the data line and retest the system.
Related
-
International Truck ISIS – Oncommand Service Information Q4.2020 [04.2020]
Navistar $85.00Rated 0 out of 5 -
CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT $45.00Rated 0 out of 5 -
Detroit Diesel Diagnostic Link DDDL 8.0 PRO PROFESSIONAL Software trucks
Detroit $25.00Rated 0 out of 5
-
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2
Trucks software $35.00Rated 0 out of 5 -
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines DT466 & DT530 (1999-2000) B
INTERNATIONAL ENGINES $29.00Rated 0 out of 5 -
SERVICE MANUAL International Engines MaxxForce DT 9 10 (2014 & Newer)
INTERNATIONAL ENGINES $17.00Rated 0 out of 5