Volvo All Engines (2004 Emissions) Fault Code: PPID 35 FMI 9 EGR Mass Flow Sensor
Fault Condition: PPID 35 will set with FMI 9 if the EGR ECU signal is missing on the J1939 serial data lines.
Possible repairs:
Turn the ignition key OFF first.
1) Remove connector A from the EGR ECU. Turn the ignition switch ON. Check for battery voltage (+12V) between pin 2 of EGR ECU connector A and a known good ground. If battery voltage is NOT present, a problem exists between EGR ECU connector A pin 2 and the power supply from the EMS Relay. Inspect the EGR ECU and EMS Relay connectors for damaged or loose pins. If the connectors are in good condition, locate and repair the open circuit, and retest the system.
2) Measure the resistance between EGR ECU connector A pin 1 and a known good ground. If the measured resistance does not indicate acceptable continuity to ground, a problem exists between EGR ECU connector A and
ground. Locate and repair the problem and retest the system.
3) Disconnect harness connector B from the Engine Management System (EMS) Module. Disconnect harness connector A from the EGR ECU. Measure the resistance between Engine Management System (EMS) Module connector B pin 52 and EGR ECU connector A pin 3. If the measured resistance does NOT indicate continuity, locate and repair the open circuit in the J1939 circuit between the Engine Management System (EMS) Module and the EGR ECU.
4) Disconnect harness connector B from the Engine Management System (EMS) Module. Disconnect harness connector A from the EGR ECU. Measure the resistance between Engine Management System (EMS) Module
connector B pin 56 and EGR ECU connector A pin 6. If the measured resistance does NOT indicate continuity, locate and repair the open circuit in the J1939 circuit between the (EMS) Module and the EGR ECU.
5) Replace the EGR ECU and Mass Flow Sensor Assembly with a known good unit. Check the system for diagnostic codes. If code PPID 35 is still set, reinstall the original EGR ECU and replace the EMS Module. Retest the system.
If code PPID 35 is NOT set, replacing the EGR ECU and Mass Flow Sensor Assembly has corrected the problem.
Related
-
Eaton Service Ranger 4.9 Engineering 4.9 [05.2021] Engineering Level ( 1 PC )
Eaton $67.00Rated 0 out of 5 -
2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )
Trucks software $85.00Rated 0 out of 5 -
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce DT 9 10 (2007-2009)
INTERNATIONAL ENGINES $30.00Rated 0 out of 5 -
SERVICE MANUAL DETROIT DIESEL DDEC III-IV Single ECM Troubleshooting Guide
DETROIT $48.00Rated 0 out of 5 -
SERVICE MANUAL DETROIT DIESEL EPA 07, EPA 10, GHG 14 TROUBLESHOOTING
DETROIT $38.00Rated 0 out of 5