Volvo All Engines (2004 Emissions) Fault Code: PPID 35 FMI 3 EGR Mass Flow Sensor
Fault Condition: PPID 35 will set with FMI 3 if the EGR ECU detects a short circuit to voltage in the exhaust gas temperature probe circuit.
Possible repairs:
Turn the ignition key OFF first.
1)If the FMI is 3 (voltage high/open) or 5 (current low/open), replace the EGR Mass Flow Sensor assembly and retest the system.
2)Remove connector A from the EGR ECU. Turn the ignition switch ON. Check for battery voltage (+12V) between pin 2 of EGR ECU connector A and a known good ground. If battery voltage is NOT present, a problem exists between EGR ECU connector A pin 2 and the power supply from the EMS Relay. Inspect the EGR ECU and EMS Relay connectors for damaged or loose pins. If the connectors are in good condition, locate and repair the open circuit, and retest the system.
3) Measure the resistance between EGR ECU connector A pin 1 and a known good ground. If the measured resistance does not indicate acceptable continuity to ground, a problem exists between EGR ECU connector A and
ground. Locate and repair the problem and retest the system.
4) Disconnect harness connector B from the Engine Management System (EMS) Module. Disconnect harness connector A from the EGR ECU. Measure the resistance between Engine Management System (EMS) Module connector B pin 52 and EGR ECU connector A pin 3. If the measured resistance does NOT indicate continuity, locate and repair the open circuit in the J1939 circuit between the Engine Management System (EMS) Module and the EGR ECU.
5) Disconnect harness connector B from the Engine Management System (EMS) Module. Disconnect harness connector A from the EGR ECU. Measure the resistance between Engine Management System (EMS) Module
connector B pin 56 and EGR ECU connector A pin 6. If the measured resistance does NOT indicate continuity, locate and repair the open circuit in the J1939 circuit between the (EMS) Module and the EGR ECU.
6) Replace the EGR ECU and Mass Flow Sensor Assembly with a known good unit. Check the system for diagnostic codes. If code PPID 35 is still set, reinstall the original EGR ECU and replace the EMS Module. Retest the system.
If code PPID 35 is NOT set, replacing the EGR ECU and Mass Flow Sensor Assembly has corrected the problem.
Related
-
Wabco ToolBox plus 13.7.0.1 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5 -
DETROIT DDDL 8.14 SP3 – Detroit Diesel Diagnostic Link 8.14 SP3 2021 ( 1PC )
Detroit $73.00Rated 0 out of 5
-
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2
Trucks software $35.00Rated 0 out of 5 -
DOWNLOAD NISSAN UD DIESEL PC-CONSULT DIAGNOSTIC 1.1.13 & PC-REPROMASTER 1.2.0
NISSAN UD $100.00Rated 0 out of 5 -
premium volvo tech tool update 2.8.150 diagnostic software 1pc
Trucks software $150.00Rated 0 out of 5 -
10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C
CAT $110.00Rated 0 out of 5 -
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 1.1.19.1 with keygen unlocked ( Hino trucks )
Hino $50.00Rated 0 out of 5 -
Navistar international OnCommand service information 2018 software trucks
Navistar $50.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL Eaton Gen III Automated TransmissionsTRSM0930 EN-USOctober 2020
TRUCK MANUALS $24.00Rated 0 out of 5 -
SERVICE MANUAL DETROIT DIESEL EPA 07, EPA 10, GHG 14 TROUBLESHOOTING
DETROIT $38.00Rated 0 out of 5