Volvo All Engines (2004 Emissions) Fault Code: PPID 122 FMI 4 Engine Compression Brake
Fault Condition: This fault can only be detected if the engine brake is demanded ON. If the fault clears, the compression brake system will not be enabled until the power is cycled.
The engine brake must be operated to ensure the fault has been cleared. The engine brake can only be operated with the engine oil temperature above 131ºF (55ºC), the vehicle moving and the engine speed above 1200rpm.
FMI 4 indicates there is a short circuit to ground in the Engine Compression Brake Solenoid control circuit.
Possible repairs:
Turn the ignition key OFF first.
1) If code PPID 122 is not set, wiggle the harness and connectors to try to set the code. Visually inspect the EMS Module harness connector and wires for frayed or loose connections.
2) Disconnect the Engine Management System (EMS) Module connector B. Measure the voltage between the EMS Module connector B pin 30 and a good ground. If voltage is present, the control line circuit is shorted to voltage. Locate the short to voltage, repair the circuit and retest the system. If there is NO voltage present, verify the diagnostic code, the FMI and retest the system. If the FMI 3 is still active, replace the EMS Module and retest the system.
3) Disconnect the Engine Management System (EMS) Module connector B. Disconnect the Engine Compression Brake Solenoid. Check for continuity between the EMS Module connector B pin 30 and a good ground.
If continuity exists to ground, replace the Engine Compression Brake Solenoid or locate and repair the short circuit to ground. If there is NO continuity, verify the diagnostic code, the FMI and retest the system. If the FMI 4 is still active, replace the EMS Module and retest the system.
4) Disconnect the Engine Management System (EMS) Module connector B. Disconnect the Engine Compression Brake Solenoid. Check for continuity between the EMS Module connector B pin 30 and Engine
Compression Brake Solenoid connector pin 1. If there is NO continuity, repair the circuit between the EMS Module and the Engine Compression Brake Solenoid.
5) Disconnect the Engine Compression Brake Solenoid. Check for continuity between the Engine Compression Brake Solenoid connector pin 2 and fuse 43 (ENG COMPT # 1) connector B. If there is NO continuity, replace the Engine Compression Brake Solenoid or repair the circuit between the fuse 43 and the Engine Compression Brake Solenoid.
6) Disconnect the Engine Management System (EMS) Module connectors A and B. Visually inspect EMS Module connectors for dirt, loose pins or deformed contacts. If a repairable open is found or the terminal feels loose, repair the harness connector. If the test lead is making good contact with the connector terminal, verify the diagnostic code, the FMI and retest the system. If the FMI 5 is still active, replace the EMS Module and retest the system.
Related
-
CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )
CAT $65.00Rated 0 out of 5
-
Scania SDP3 2.48.6 Diagnosis & Programming for VCI 3 VCI3 without Dongle
Scania $30.00Rated 0 out of 5 -
JPRO 2022 v1 Commercial Vehicle Diagnostics V1 Software Download & Installation Service ( 1 PC )
JPRO $94.00Rated 0 out of 5 -
PACCAR Electronic Service Analyst 5.4.3.0 SW files 27.03.2021 software trucks
PACCAR $60.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1892 Throttle Position Sensor Pulse Width Modulation (PWM) Signal High Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines DT466 (2004-2006)
INTERNATIONAL ENGINES $45.00Rated 0 out of 5