Volvo All Engines (2004 Emissions) Fault Code: PID 98 FMI 4 Engine Oil Level / Temperature Sensor
Fault Condition: If the EMS Module senses that the engine oil level is moderately or critically below range, FMI 1 will be set. If the reference voltage signal is shorted to ground, FMI 4 will be set. If the reference voltage circuit is shorted to battery voltage or has an open circuit, FMI 5 will be set. If the ground circuit of the sensor has an open, FMI 5 will also be set.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect the Engine Oil Temperature/Level Sensor connector.Check for continuity between each of the pins (1,2,3, and 4) of the Engine Oil Temperature/Level Sensor and a good ground. If continuity exists between any of the pins and ground, replace the Engine Oil Temperature/Level Sensor.
2) Disconnect the Engine Oil Temperature/Level Sensor connector. Measure the resistance across the pins 1 and 2 of the Engine Oil Temperature/Level Sensor. With the engine at room temperature the sensor resistance should be 10.8-17.4 ohms. If the resistance of the sensor is NOT as specified, replace the Engine Oil Temperature/Level Sensor.
3) Disconnect the Engine Oil Temperature/Level Sensor harness connector. Disconnect the EMS Module harness connector B. Measure continuity between Engine Oil Temperature/Level Sensor harness connector pin 2 and a good ground. If continuity exists, repair the short to ground in the signal line circuit. If there is NO continuity, check the pins or the EMS Module for dirt, loose pins or deformed contacts. Replace the EMS Module if the pins of the module are not damaged. Retest the system.
4) Disconnect the Engine Oil Temperature/Level Sensor connector. Measure the resistance across the pins 1 and 2 of the Engine Oil Temperature/Level Sensor. With the engine at room temperature the sensor resistance should be 10.8-17.4 ohms. If the resistance of the sensor is NOT as specified, replace the Engine Oil Temperature/Level Sensor.
5) Disconnect the Engine Oil Temperature/Level Sensor harness connector. Disconnect the EMS Module harness connector B. Turn the ignition key ON. Measure voltage between Engine Oil Temperature/Level Sensor harness
connector pin 2 and a good ground. If the there is voltage present, repair the short to voltage on the signal line.
6) Disconnect the Engine Oil Temperature/Level Sensor connector. Disconnect connector B from the EMS Module. Check for continuity between connector B pin 4 of the EMS Module harness connector and pin 2 of the Engine Oil Temperature/Level Sensor harness connector. If there is NO continuity, locate and repair the circuit between the sensor and the EMS Module.
7) Disconnect the Engine Oil Temperature/Level Sensor connector. Disconnect connector B from the EMS Module. Check for continuity between connector B pin 3 of the EMS Module harness connector and pin 1 of the Engine Oil Temperature/Level Sensor harness connector. If there is NO continuity, locate and repair the circuit between the sensor and the EMS Module.
8) Visually inspect the EMS Module harness connectors A and B for dirt, loose pins or deformed contacts. If a repairable open is found or either of the pins feels loose, repair the EMS Module harness connector.
If the EMS Module harness connector is OK, verify the diagnostic code and the FMI, and retest. If FMI 5 is still active, replace the Engine Management System (EMS) Module and retest the system.
Related
-
download MANCATS II v14.01 2014 Diagnostic software MAN CATS ( virtual machine )
MAN $75.00Rated 0 out of 5 -
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5 -
DOWNLOAD Paccar ESA Electronic Service Analyst 5.5.0 Diagnostic Software 2023
PACCAR $96.00Rated 0 out of 5
-
JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023
John Deere $250.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5 -
CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT $45.00Rated 0 out of 5 -
Detroit Diesel Diagnostic Link DDDL 8.0 PRO PROFESSIONAL Software trucks
Detroit $25.00Rated 0 out of 5 -
Wabco ToolBox plus 13.7.0.1 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce 11 & 13 (2014 & Newer)
INTERNATIONAL ENGINES $20.00Rated 0 out of 5 -
SERVICE MANUAL International Engines DT466E & DT530E (1999 & Older)
INTERNATIONAL ENGINES $31.00Rated 0 out of 5