Volvo All Engines (2004 Emissions) Fault Code: PID 97 FMI 4 Water in Fuel Filter Sensor
Fault Condition: This fault will become active when the EMS Module detects that the Water In Fuel Filter supply voltage is above or below preset specifications. Actual water in the fuel filter will not produce a fault.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect EMS Module connector B and the Water In Fuel Filter (WIFF) Sensor connector. Measure for continuity between EMS Module harness connector B pin 8 and pin 3 of the WIFF Sensor harness connector.
If there is NO continuity, repair the open in the harness reference voltage line.
2) Disconnect EMS Module connector B and the Water In Fuel Filter (WIFF) Sensor connector. Measure for continuity between EMS Module harness connector B pin 8 and a good ground. If continuity exists, repair the short to ground in the harness voltage line and retest the system.
3) Disconnect EMS Module connector B and the Water In Fuel Filter (WIFF) Sensor connector. Measure for continuity between EMS Module harness connector B pin 10 and pin 2 of the WIFF Sensor harness connector. If there is NO continuity, repair the open in the harness reference line.
4) Visually inspect EMS Module connectors A and B for dirt, loose or shorted pins or deformed contacts. If a repairable open or short is found, or the terminal feels loose, repair EMS Module harness connector.
5) Connect EMS Module connectors A and B. Connect the WIFF Sensor connector. Turn the ignition key ON. If code PID 97 is still active, replace the Water In Fuel Filter (WIFF) Sensor and retest the system. If code PID 97 is still
active, check the EMS Module and connectors A and B for dirt, loose or shorted pins, or any other repairable damage. If no problems are evident, or are NOT repairable, replace the EMS Module and retest the system.
If code PID 97 is NOT active, the diagnostic procedures have corrected the problem. Check all connectors to ensure proper contact.
6) Disconnect the EMS Module harness connectors A and B. Disconnect the harness connector from the Water In Fuel Filter Sensor. Turn the ignition key ON. Measure the battery voltage between pin 3 of the Water In Fuel Filter Sensor connector and a good ground. If there is approximately battery voltage, locate and repair the short to voltage in the signal line. If 0 volts is measured, replace the EMS Module and retest the system.
Related
-
2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )
Trucks software $85.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5
-
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5 -
JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023
John Deere $250.00Rated 0 out of 5 -
premium volvo tech tool update 2.8.150 diagnostic software 1pc
Trucks software $150.00Rated 0 out of 5 -
DOWNLOAD Paccar ESA Electronic Service Analyst 5.5.0 Diagnostic Software 2023
PACCAR $96.00Rated 0 out of 5 -
JPRO 2022 v1 Commercial Vehicle Diagnostics V1 Software Download & Installation Service ( 1 PC )
JPRO $94.00Rated 0 out of 5 -
Navistar international OnCommand service information 2018 software trucks
Navistar $50.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5