Volvo All Engines (2004 Emissions) Fault Code: PID 252 FMI 9 Date Data Failure
Fault Condition: The Date Data Failure code will set when the Engine Management System (EMS) Module has lost the date stamps that are sent from the Instrument Cluster Module (ICM). The date stamps will be substituted by the Engine Management System (EMS) Module.
Possible repairs:
Turn the ignition key OFF first.
1) Connect a diagnostic computer. Turn the ignition key ON. Use the diagnostic computer to attempt to communicate with the Instrument Cluster Module (ICM). If communication can be made with the Instrument Cluster Module (ICM), the fault may be intermittent, wiggle the harness and connectors to try to set the code. If fault in the harness is found, repair or replace the harness.
2) Disconnect connector A from the Instrument Cluster Module (ICM). Check continuity between the Instrument Cluster Module (ICM) harness connector A pin 2 and a good ground. If continuity does not exist, locate and repair the open in the circuit.
3) Disconnect connector A from the Instrument Cluster Module (ICM). Turn the ignition key ON. Measure the voltage between connector A pin 1 and/or 3 of the Instrument Cluster Module (ICM) and a good ground. If the measured voltage is not approximately battery voltage, locate and repair the short or open in the harness. If a short or open in the harness is not found, check the Instrument Cluster Module (ICM) connectors for the dirt or damage. If the Instrument Cluster Module (ICM) Harness Connector pins are making good contact, replace the Instrument Cluster Module (ICM) and retest the system.
4) Disconnect INST. CLSTR fuse F19. Disconnect connector A from the Instrument Cluster Module (ICM). Turn the ignition key ON. Measure the voltage between Instrument Cluster Module (ICM) harness connector A
pin 1 and a good ground (see Figure 159). If voltage is present, locate and repair the short to power in the harness.
5) Disconnect INSTR. CLUSTER fuse F63. Disconnect connector A from the Instrument Cluster Module (ICM). Turn the ignition key ON. Measure the voltage between Instrument Cluster Module (ICM) harness connector A pin 3 and a good ground. If voltage is present, locate and repair the short to power in the harness.
6) Connect all connectors to the Instrument Cluster Module (ICM) Install Cluster fuses F19 and F63. Turn the ignition key ON. If code P252 is still active, replace the Instrument Cluster Module (ICM) and retest the system.
If code P252 is NOT active, the procedures have corrected the problem. Check all connectors to ensure proper connections.
Related
-
Volvo Impact 2021 Trucks & Buses 06.2021 DVD 9116 Spare Parts Catalog
Trucks software $55.00Rated 0 out of 5 -
Scania SDP3 2.48.6 Diagnosis & Programming for VCI 3 VCI3 without Dongle
Scania $30.00Rated 0 out of 5 -
DPF EGR SCR BAC ERG Delete & Flash CAAT Cummings Detroit Dodge Mack Volvo Collection of DELETE files
CAT $200.00Rated 0 out of 5 -
DOWNLOAD Paccar ESA Electronic Service Analyst 5.5.0 Diagnostic Software 2023
PACCAR $96.00Rated 0 out of 5
-
ddct Detroit diesel calibration tool (DDCT) v4.5 English Include Calibrations & Metafiles
Detroit $30.00Rated 0 out of 5 -
Volvo PROSIS Offline 2019 Parts Catalog Installation Service
Trucks software $45.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce 11 & 13 (2014 & Newer)
INTERNATIONAL ENGINES $20.00Rated 0 out of 5 -
service manual TroubleshootingManual Allison TransmissionMD/HD/B -Series -TransmissionsWTEC II Controls
Allison $25.00Rated 0 out of 5 -
SERVICE MANUAL INTERNATIONAL ENGINE VT275 (2005 & Newer)
INTERNATIONAL ENGINES $27.00Rated 0 out of 5