Volvo All Engines (2004 Emissions) Fault Code: PID 251 FMI 9 Time Data Failure
Fault Condition: The Time Data Failure code will set when the Engine Management System (EMS) Module has lost the time stamps that are sent from the Instrument Cluster Module (ICM). The time stamps will be substituted by the Engine Management System (EMS) Module.
Possible repairs:
Turn the ignition key OFF first.
1) Verify that code PID 251 is set. If code PID 251 is not set, wiggle the harness and connectors to try to set the code. Visually inspect the ABS connectors and wires for poor connections.
2) Connect a diagnostic computer. Turn the ignition key ON. Use the diagnostic computer to attempt to communicate with the Instrument Cluster Module (ICM). If communication can be made with the Instrument Cluster Module (ICM), the fault may be intermittent, wiggle the harness and connectors to try to set the code. If fault in the harness is found, repair or replace the harness.
3) Disconnect connector A from the Instrument Cluster Module (ICM). Check continuity between the Instrument Cluster Module (ICM) harness connector A pin 2 and a good ground (see Figure 150).
If continuity does not exist, locate and repair the open in the circuit.
4) Disconnect connector A from the Instrument Cluster Module (ICM). Turn the ignition key ON. Measure the voltage between connector A pin 1 of the Instrument Cluster Module (ICM) Harness Connector and a good ground.
If the measured voltage is not approximately battery voltage, locate and repair the short or open in the harness. If a short or open in the harness is not found, check the Instrument Cluster Module (ICM) connectors for the dirt or damage. If the Instrument Cluster Module (ICM) pins are making good contact, replace the Instrument Cluster Module (ICM) and retest the system.
5) Disconnect connector A from the Instrument Cluster Module (ICM). Turn the ignition key ON. Measure the voltage between connector A pin 3 of the Instrument Cluster Module (ICM) Harness Connector and a good ground.
If the measured voltage is not approximately battery voltage, locate and repair the short or open in the harness. If a short or open in the harness is not found, check the Instrument Cluster Module (ICM) connectors
for the dirt or damage. If the Instrument Cluster Module (ICM) pins are making good contact, replace the Instrument Cluster Module (ICM) and retest the system.
6) Disconnect INST. CLSTR fuse F19. Disconnect connector A from the Instrument Cluster Module (ICM). Turn the ignition key ON. Measure the voltage between Instrument Cluster Module (ICM) harness connector A
pin 1 and a good ground. If voltage is present, locate and repair the short to power in the harness.
7) Disconnect INSTR. CLUSTER fuse F63. Disconnect connector A from the Instrument Cluster Module (ICM). Turn the ignition key ON. Measure the voltage between Instrument Cluster Module (ICM) harness connector A pin 3 and a good ground. If voltage is present, locate and repair the short to power in the harness.
8) Connect all connectors to the Instrument Cluster Module (ICM). Install Cluster fuses F19 and F63. Turn the ignition key ON. If code P251 is still active, replace the Instrument Cluster Module (ICM) and retest the system.
If code P251 is NOT active, the procedures have corrected the problem. Check all connectors to ensure proper connections.
Related
-
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2
Trucks software $35.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines DT466 & DT530 (2001-2003) C
INTERNATIONAL ENGINES $31.00Rated 0 out of 5 -
SERVICE MANUAL DETROIT DIESEL DDEC III-IV Single ECM Troubleshooting Guide
DETROIT $48.00Rated 0 out of 5