Volvo All Engines (2004 Emissions) Fault Code: PID 172 FMI 4 Intake Air and Humidity Sensor
Fault Condition: The Electronic Malfunction Lamp (EML) will turn on and PID 172 will set when the Engine Management System (EMS) Module senses that the Intake Air Temperature Sensor signal voltage is less than 0.5 volts or greater than 4.9 volts for 1 second. If the Intake Air Temperature Sensor voltage returns to between 0.5 volts and 4.9 volts for more than 1 second, the fault will become inactive.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect the Intake Air Temperature and Humidity (IATH) Sensor connector. Measure the resistance between pins 3 and 4 of the Intake Air Temperature and Humidity (IATH) Sensor with the ambient air temperature between 32° and 104°F (0° and 40°C) If the measured resistance is NOT between 30029 and 5575 ohms, replace the sensor.
2) Disconnect the Intake Air Temperature and Humidity (IATH) Sensor connector. If continuity exists on any pin, replace the Intake Air Temperature and Humidity (IATH) Sensor.
3) Disconnect the Intake Air Temperature and Humidity (IATH) Sensor harness connector. Measure the resistance between pins 3 and 4 of the Intake Air Temperature and Humidity (IATH) Sensor with the ambient air temperature between 32° and 104°F (0° and 40°C). If the measured resistance is NOT between 30029 and 5575 ohms, replace the Intake Air Temperature and Humidity (IATH) Sensor.
4) Connect the Intake Air Temperature and Humidity (IATH) Sensor harness connector. Connect connectors to the Engine Management System (EMS) Module. Turn the ignition key ON. If PID 172 is still active, check the Engine
Management System (EMS) Module and connector A for dirt, loose or shorted pins, or any other repairable damage. If no problems are evident or are not repairable, replace the Engine Management System (EMS) Module
and retest the system. If PID 172 is NOT active, the diagnostic procedures have corrected the problem. Check all connectors to ensure proper connections.
5) Disconnect the Intake Air Temperature and Humidity (IATH) Sensor harness connector. Disconnect Engine Management System (EMS) Module harness connectors A and B. Check for continuity between Engine
Management System (EMS) Module harness connector A pin 43 and all other pins on Engine Management System (EMS) Module connectors A and B. If continuity exists, the signal line is shorted to one of the other Engine Management System (EMS) Module circuits. Locate and repair the short circuit to voltage, then replace the sensor. If there is NO continuity, the signal line is shorted to voltage somewhere else in the harness. Locate and repair the short circuit to voltage, then replace the sensor.
6) Connect the Intake Air Temperature and Humidity (IATH) Sensor harness connector. Connect connector A to the Engine Management System (EMS) Module. Turn the ignition key ON. If PID 172 is still active, check the Engine
Management System (EMS) Module and connectors A, and B for dirt, loose or shorted pins, or any other repairable damage. If no problems are evident or are not repairable, replace the Engine Management System (EMS) Module and retest the system. If PID 172 is NOT active, the diagnostic procedures have corrected the problem. Check all connectors to ensure proper connections.
Related
-
Eaton Service Ranger 4.9 Engineering 4.9 [05.2021] Engineering Level ( 1 PC )
Eaton $67.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce DT 9 10 (2014 & Newer)
INTERNATIONAL ENGINES $17.00Rated 0 out of 5 -
SERVICE MANUAL INTERNATIONAL ENGINE VT275 (2005 & Newer)
INTERNATIONAL ENGINES $27.00Rated 0 out of 5 -
SERVICE MANUAL International Engines MaxxForce DT 9 10 (2010-2013)
INTERNATIONAL ENGINES $20.00Rated 0 out of 5