Cummins ISC CM2150 (2007-09) Fault Code: 555 (ISB/QSB3.3) PID: 101 SPN: 101 FMI: 0 Crankcase Pressure – Data Valid but Above Normal Operational Range – Moderately Severe Level.
Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM. Use the following procedure in the corresponding Troubleshooting and Repair Manual for the engine being serviced.
Possible causes:
1)Crankcase ventilation filter needs to be replaced
2)Crankcase pressure sensor damage
3)Malfunctioning or misassembled closed crankcase ventilation valve
4)Frozen, plugged, or restricted crankcase ventilation hose
5)Plugged or restricted crankcase ventilation hose
6)Plugged or restricted crankcase ventilation oil drain tube or check valve
7)Plugged or restricted crankcase breather tube (Rear Engine Mounted Crankcase Ventilation Filter)
8)High air intake restriction.
Depending on the breather system used, the crankcase ventilation filter will be located:
•On top of the rocker lever cover, between the rocker lever cover and the crankcase ventilation filter cover.
•At the rear of the engine, encased in an external crankcase ventilation filter housing that mounts to the flywheel housing.
Both systems are closed crankcase breather systems, meaning the crankcase gases are vented into the intake system at the inlet to the turbocharger compressor.
It is important to check for plugged or restricted hoses, tubes, check valves, and filters in extreme cold ambient temperatures.
If Fault Code 555 becomes active due to a plugged filter before the maintenance interval is reached or the filter plugs frequently, see the High Blowby (Crankcase Gases (Blowby) Excessive) troubleshooting symptom tree.
Possible repairs:
1)Replace the crankcase pressure sensor.
2)Replace the crankcase ventilation filter.
3)Replace the crankcase breather element.
4)Correct or replace the crankcase ventilation valve.
5)Clean or replace the crankcase ventilation oil drain tubes, check valves, or breather tube.
6)Replace the crankcase ventilation hose.
7)Repair the air intake restriction.
Related
-
volvo Devtool Studio V2 / V3 / V4 Developer tool plus 2.6 / 2.7
Trucks software $35.00Rated 0 out of 5 -
VOLVO PREMIUM TECH TOOL PTT 2.7.30 Developer + Devtool + INSTALATION VIDEO!
Trucks software $60.00Rated 0 out of 5 -
John Deere & Hitachi Parts ADVISOR 2020 [08.2020] Offline DVD Spare Parts Catalog
John Deere $120.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1892 Throttle Position Sensor Pulse Width Modulation (PWM) Signal High Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5