ISC CM2150 (2007-09)

Showing 61–72 of 210 results

Default sorting Sort by popularity Sort by average rating Sort by latest Sort by price: low to high Sort by price: high to low

• 

  Cummins ISC CM2150 (2007-09) Fault Code: 197 PID: 111 SPN: 111 FMI: 1 Coolant Level – Data Valid but Below Normal Operating Range – Moderately Severe Level. Low engine coolant level detected.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 1972 PID: SPN: 3245 FMI: 0 Exhaust Gas Temperature 3 – Data Valid but Above Normal Operational Range – Moderately Severe Level. The aftertreatment diesel particulate filter outlet temperature sensor reading has exceeded the maximum temperature limit.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 1973 PID: SPN: 3245 FMI: 0 Exhaust Gas Temperature 3 – Data Valid but Above Normal Operational Range – Most Severe Level. The aftertreatment diesel particulate filter outlet temperature sensor reading has exceeded the maximum engine protection temperature limit.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 1974 PID: 101 SPN: 101 FMI: 0 Crankcase Pressure – Data Valid but Above Normal Operational Range – Least Severe Level. The crankcase breather filter requires maintenance.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 1981 PID: SID 324 SPN: 3926 FMI: 0 Aftertreatment Particulate Filter Differential Pressure – Data Valid but Above Normal Operational Range – Least Severe Level. The aftertreatment differential pressure has exceeded the maximum operating limits or the diesel particulate filter is plugged.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 1993 PID: 3064 SPN: FMI: 11 Aftertreatment Particulate Trap Missing – Condition Exists. The aftertreatment diesel particulate filter in the exhaust system is not present.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 2182 PID: SID 79 SPN: 1072 FMI: 3 Engine Brake Actuator Driver 1 Circuit – Voltage Above Normal or Shorted to High Source. High voltage or open circuit detected at the engine brake solenoid number 1 signal circuit.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 2183 PID: SID 79 SPN: 1072 FMI: 4 Engine Brake Actuator Circuit #1 – Voltage Below Normal or Shorted to Low Source. Low voltage detected at the engine brake solenoid number 1 signal circuit.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 2185 PID: SID 232 SPN: 3512 FMI: 3 Sensor Supply 4 Circuit – Voltage Above Normal or Shorted to High Source. High voltage detected at +5 volt sensor supply circuit to the accelerator pedal position sensor.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 2186 PID: SID 232 SPN: 3512 FMI: 4 Sensor Supply 4 Circuit – Voltage Below Normal or Shorted to Low Source. Low voltage detected at the +5 volt sensor supply circuit to the accelerator pedal position sensor.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 2195 PID: SID 51 SPN: 703 FMI: 14 Auxiliary Equipment Sensor Input 3 Engine Protection Critical – Special Instructions. The emergency door of the vehicle has been detected open.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISC CM2150 (2007-09) Fault Code: 2198 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Root Cause Not Known. Intermittent communication between the smart VGT controller and the ECM has been detected. The VGT controller is not interpreting the J1939 message from the ECM correctly.

  Cumminz

  Rated 0 out of 5