Detroit DD16 GHG14 (2014-16) Fault Code: SPN 1327 FMI 31 (MCM) Idle Smoothness Control/Cylinder #5 Misfire at Idle
DESCRIPTION:
This fault code sets when the motor control module (MCM) detects that cylinder #5 has low rpm speed with the injector commanded to max fueling for a count of two with all conditions met.
MONITORED PARAMETER:
Engine rpm
TYPICAL ENABLING CONDITIONS:
1. Engine speed steady between 600 to 950 rpm.
2. Engine coolant temperature between 65°C (149°F) and 114°C (237°F).
3. Engine fuel temperature between 0°C (32°F) and 150°C (302°F).
MONITOR SEQUENCE:
None
EXECUTION FREQUENCY:
Once per drive cycle when enabling conditions are met.
TYPICAL DURATION:
5 seconds
DASH LAMPS:
1. CEL
2. MIL
ENGINE REACTION:
25% date
VERIFICATION:
1. Ensure the ignition has been off for a minimum of 5 minutes prior to the last ignition on.
2. Meet all enabling conditions.
3. Let the engine idle for 5 minutes.
4. Fault code status will become pending with one detected failure and active with the second.
NOTE: Do not use the idle speed balance (ISB) test in the diagnostic service tool for any misfire at idle testing.
POSSIBLE CAUSES:
1. Valve lash out of adjustment.
2. Valve train damage/failure.
3. Bent valve.
4. Valve face/seat damage.
5. Stuck Jake brake.
6. Bearing failure.
7. Bent connecting rod.
8. Cylinder liner damage.
9. Piston ring damage.
10. Failed cylinder head gasket.
11. Failed fuel injector.
PROBABLE CAUSES:
1. Cylinder kit failure.
2. Valve train failure.
3. Lash adjustments.
4. Fuel injector.
5. High pressure fuel line (rail to fuel injector).
6. Debris entering fuel injector.
7. Fuel quality.
Note: If 1322-31 active, fix that first.
Related
-
DOWNLOAD NISSAN UD DIESEL PC-CONSULT DIAGNOSTIC 1.1.13 & PC-REPROMASTER 1.2.0
NISSAN UD $100.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 1.1.19.1 with keygen unlocked ( Hino trucks )
Hino $50.00Rated 0 out of 5 -
JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023
John Deere $250.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1892 Throttle Position Sensor Pulse Width Modulation (PWM) Signal High Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5