Detroit DD15 GHG14 (2014-16) Fault Code: SPN 190 FMI 0 (MCM) Engine Over Speed
DESCRIPTION:
This fault code sets when the engine speed is above 2500 rpm.
MONITORED PARAMETER:
Engine speed
TYPICAL ENABLING CONDITIONS:
Engine speed greater than idle.
MONITOR SEQUENCE:
None
EXECUTION FREQUENCY:
Continuous when enabling conditions met.
TYPICAL DURATION:
Two seconds
DASH LAMPS:
MIL
ENGINE REACTION:
Engine brakes are activated.
VERIFICATION:
Start and run the engine.
POSSIBLE CAUSES:
1. Vehicle was driven downhill in too low of a gear or without using the engine brakes.
2. Vehicle equipped with a DT12 transmission driven downhill with the engine brakes set on high.
3. Crankshaft speed sensor fault.
4. External combustible fluids drawn into the air intake.
NOTE: This fault code can be induced by the driver while the vehicle is traveling downhill.; There will be a message in the instrument cluster (IC) to warn the driver that the engine speed is too high. The check engine light (CEL) will also sets at this time. Once the engine rpm is within normal operating range, the message in the IC and the CEL will no longer be present.
NOTE: For DT12 equipped vehicles, the transmission will automatically downshift to provide higher rpms to increase Jake Brake effectiveness. This is especially true with Jake brakes in the high setting. CPC software R32 and proper versions have a target downshift speed of 2300 rpm. CPC software R33 and higher have lowered the target downshift speed to 2200 rpm to provide more margin against logging engine overspeed codes. To further prevent engine overspeed codes, if the Jake brake alone do not sloe the vehicle, it may be necessary for the driver to apply the service brakes. If maximum Jake brake effectiveness is not needed, such as vehicles that are lightly loaded or with no load, then select either the low or medium Jake brake setting to provide less aggressive downshifts.
NOTE: This is an information only code. It means the engine went after than 2500 RPM for a specified time. Talk to the driver.
-
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce 7 (2010 & Newer)
INTERNATIONAL ENGINES $34.00Rated 0 out of 5 -
SERVICE MANUAL DETROIT DIESEL DD15 , DD13 Service Workshop Repair Manual
DETROIT $25.00Rated 0 out of 5