Detroit DD13 GHG14 (2014-16) Fault Code: SPN 100 FMI 10 (MCM) Low Oil Pressure Derate
DESCRIPTION:
This fault code sets when the engine power has been limited to prevent engine damage due to a low oil pressure condition.
MONITORED PARAMETER:
Engine oil pressure
TYPICAL ENABLING CONDITIONS:
Always on
MONITOR SEQUENCE:
1. Key on
2. Engine running
EXECUTION FREQUENCY:
Continuous when enabling conditions are met.
TYPICAL DURATION:
Two seconds
DASH LAMPS:
CEL
ENGINE REACTION:
1. Engine derate.
2. Engine shut down.
3. Calibration dependent.
VERIFICATION:
Check at engine operating temperature.
NOTE: Whenever a low engine oil pressure is confirmed the crankshaft main bearings and rod bearings should be inspected for damage or excessive wear.
POSSIBLE CAUSES:
1. Failed oil pressure sensor.
2. Initial start after oil maintenance.
3. Vehicle is parked on a steep incline.
4. Improper oil level.
5. Oil dilution.
6. Leaks in the oil suction manifold.
7. Leaks at the oil suction pipes.
8. Failed oil pump.
NOTE: If 100-3 is active as well, fix 100-3 first.
NOTE: If 100-4 is active as well, fix 100-4 first.
PROBABLE CAUSES:
If oil pressure is fluctuating:
1. Oil level low or high.
2. Faulty oil gauge.
3. Cracked or loose oil pump suction pipe.
4. Loose drive or driven oil pump gear.
5. Fault oil pressure relief valve..
PROBABLE CAUSES:
If oil pressure is low but stable:
1. Fuel in oil.
2. High oil level.
-
Wabco ToolBox plus 13.7 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5 -
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5 -
DAF Davie Runtime v5.6.1 Davie XDc ll [02.2019] + Expire Fix 302.00 Unlock ( Windows 7 )
DAF $70.00Rated 0 out of 5
-
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0218 Transmission Fluid Over Temperature Condition
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines VT275 (2004 & Older)
INTERNATIONAL ENGINES $21.00Rated 0 out of 5