Cummins ISM CM875 (2003-06) Fault Code: 2215 PID: P094 SPN: 94 FMI: 1/18 Fuel Pump Delivery Pressure – Data Valid But Below Normal Operating Range – Moderately Severe Level. Low fuel pressure has been detected by the ECM.
Verify the electronic control module (ECM) calibration is correct.
It is possible to swap the connections between the aftertreatment fuel pressure sensor and the fuel delivery pressure sensor. If this occurs, Fault Code 2215 will intermittently go active and the engine will run rough and will surge at low idle. If these symptoms are present, make sure the fuel pressure connections are connected properly.
The fuel pressure is monitored by the electronic control module (ECM). If the rail fuel pressure is lower than an acceptable level for given engine operating conditions, the fault code is logged.
Possible causes:
1)A damaged or sticking drain-back valve located in the fuel supply circuit in the integrated fuel system module (IFSM) which is located directly above the fuel lift pump.
Possible repairs:
1)Properly connect the aftertreatment fuel pressure sensor and fuel delivery pressure sensor wiring harness connections.
2)Prime the fuel system.
3)Fill the fuel tanks.
4)Repair or replace the fuel lift pump.
5)Repair or replace the fuel shutoff valve.
6)Replace the 1724 kPa [250 psi] regulator.
7)Use the following procedure in the Signature?, ISX, and QSX15 Service Manual, Bulletin 3666239 for repair or replacement of the fuel pump (gear pump).
8)Locate and repair the source of the air leak by checking all the OEM supply lines and fittings, suction-side fuel filter head, fuel tank stand pipes, ECM cooling plate, and ECM cooling plate fuel supply and return lines.
9)Replace the suction-side fuel filter or repair the cause of high inlet restriction.
10)Replace the pressure fuel filter.
11)Replace the regulator.
12)For ISX CM871 and ISM CM876 engines, use the following procedure for replacement of the rail fuel pressure sensor.
-
PACCAR Electronic Service Analyst 5.4.3.0 SW files 27.03.2021 software trucks
PACCAR $60.00Rated 0 out of 5
-
Volvo PROSIS Offline 2019 Parts Catalog Installation Service
Trucks software $45.00Rated 0 out of 5 -
John Deere & Hitachi Parts ADVISOR 2020 [08.2020] Offline DVD Spare Parts Catalog
John Deere $120.00Rated 0 out of 5 -
Detroit Diesel Diagnostic Link DDDL 8.0 PRO PROFESSIONAL Software trucks
Detroit $25.00Rated 0 out of 5 -
Wabco ToolBox plus 13.7 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5 -
Eaton Service Ranger 4.9 Engineering 4.9 [05.2021] Engineering Level ( 1 PC )
Eaton $67.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
service manual TroubleshootingManual Allison TransmissionMD/HD/B -Series -TransmissionsWTEC II Controls
Allison $25.00Rated 0 out of 5