Cummins ISL CM850 (2003-06) Fault Code: 649 PID: SID 153 SPN: 1378 FMI: 11 Change Lubricating Oil and Filter – Condition Exists. Change engine oil and filter.

Related products

• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 2754 PID: SPN: 81 FMI: 16 Engine Particulate Filter Inlet Pressure – Data Valid but Above Normal Operational Range – Moderately Severe Level. Excessive black smoke has been detected exiting the engine and entering the aftertreatment diesel particulate filter.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Cummins ISX CM870 (2003-06) Fault Code: 426 PID: S231 SPN: 639 FMI: 2/2 Communication between the electronic control module (ECM) and another device on the SAE J1939 data link has been lost.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISX CM870 (2003-06) Fault Code: 731 PID: S064 SPN: 723 FMI: 7/7 Engine Speed Sensor and Camshaft Position Sensor – Mechanical Misalignment Between Camshaft and Crankshaft Sensors. Engine position signal from the engine speed sensor and camshaft position sensor do not match.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2635 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Condition Exists. A calibration mismatch between the VGT actuator and the ECM has been detected.

  Cumminz

  Rated 0 out of 5
• 

  Allison 1000 and 2000 Series Gen 4 (2005-11) Service manual

  Allison $10.00

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 427 PID: SID 231 SPN: 639 FMI: 9 J1939 Datalink – Abnormal Update Rate. Communication between the electronic control module (ECM) and another device on the SAE J1939 data link has been lost.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 115 PID: 115 SPN: 115 FMI: 2 Engine Magnetic Speed/Position Lost Both of Two Signals – Data Erratic, Intermittent, or Incorrect. The engine control module (ECM) has detected that the primary and backup speed sensor signals are connected backwards.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISX CM870 (2003-06) Fault Code: 551 (NISS) PID: S230 SPN: 558 FMI: 4/4 Accelerator Pedal Idle Validation Circuit – data incorrect. No voltage detected simultaneously on both idle validation and off-idle validation switches.

  Cumminz

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 1242 PID: 91 SPN: 91 FMI: 2 Accelerator Pedal or Lever Position Sensor 1 and 2 – Data Erratic, Intermittent, or Incorrect. Accelerator position sensor number 1 and number 2 are reading different values.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 1242 PID: 91 SPN: 91 FMI: 2 Accelerator Pedal or Lever Position Sensor 1 and 2 – Data Erratic, Intermittent, or Incorrect. Accelerator position sensor number 1 and number 2 are reading different values.

  Cumminz

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 1663 PID: SPN: 3241 FMI: 11 Catalyst Inlet Temperature Sensor Swapped with Outlet – Condition Exists. The inlet and outlet catalyst temperature sensor connections are swapped.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Cummins ISX CM870 (2003-06) Fault Code: 649 PID: S153 SPN: 1378 FMI: 11/31 Change Lubricating Oil and Filter. Maintenance Monitor feature indicates the engine is due for a lubricating oil and filter change.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2636 PID: SID 027 SPN: 641 FMI: 9 VGT Actuator Driver Circuit – Abnormal Update Rate. No communications on the J1939 data link between the engine ECM and the smart VGT controller.

  Cumminz

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 2636 PID: SID 027 SPN: 641 FMI: 9 VGT Actuator Driver Circuit – Abnormal Update Rate. No communications on the J1939 data link between the engine ECM and the smart VGT controller.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Perkins SPI2 2018A Dealer Parts and Service

  Perkins $50.00

  Rated 0 out of 5