Cummins ISL CM850 (2003-06) Fault Code: 415 (Sensor) PID: 100 SPN: 100 FMI: 11 Engine Oil Rifle Pressure – Data Valid but Below Normal Operational Range – Most Severe Level. Oil pressure signal indicates oil pressure is below the engine protection critical limit.

Related products

• 

  Cummins ISB4.5 CM2150 Fault Code: 3141 PID: 102 SPN: 3667 FMI: 4 Engine Air Shutoff Sensor Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 111 PID: 629 FMI:12 Engine Control Module Critical Internal Failure – Bad Intelligent Device or Component

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2555 PID: SPN: 729 FMI: 3 Engine Intake Air Heater 1 Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 731 PID: SID 64 SPN: 723 FMI: 7 Engine Speed/Position Camshaft and Crankshaft Misalignment – Mechanical System Not Responding or Out of Adjustment.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2265 PID: SID 126 SPN: 1075 FMI: 3 Electric Lift Pump for Engine Fuel Supply Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2322 PID: SID 64 SPN: 723 FMI: 2 Engine Camshaft Speed/Position Sensor – Data Erratic, Intermittent, or Incorrect.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2371 PID: SPN: 1074 FMI: 3 Engine (Exhaust) Brake Driver Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2183 PID: 477 SPN: 1072 FMI: 4 Engine Brake Actuator Driver 1 Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2363 PID: SID 29 SPN: 1073 FMI: 4 Engine Brake Actuator Driver Output 2 Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 3737 PID: SID 115 SPN: 1675 FMI: 11 Engine Starter Mode Overcrank Protection – Condition Exists.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2367 PID: SID 80 SPN: 1073 FMI: 3 Engine Brake Actuator Driver Output 2 Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 3697 PID: SID 254 SPN: 630 FMI: 12 Engine Control Module Calibration Memory – Bad Intelligent Device or Component.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2266 PID: SID 126 SPN: 1075 FMI: 4 Electric Lift Pump for Engine Fuel Supply Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 4484 PID: SPN: 4484 FMI: 7 Engine Air Shutoff Circuit – Mechanical System Not Responding or Out of Adjustment.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2321 PID: 190 SPN: 190 FMI: 2 Engine Crankshaft Speed/Position – Data Erratic, Intermittent, or Incorrect.

  Cumminz

  Rated 0 out of 5