Cummins ISL CM850 (2003-06) Fault Code: 412 PID: SID 250 SPN: 608 FMI: 2 SAE J1587/J1922 data link – can not transmit. Communication between the ECM and another device on the J1587/J1922 data link has been lost.

Related products

• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 2754 PID: SPN: 81 FMI: 16 Engine Particulate Filter Inlet Pressure – Data Valid but Above Normal Operational Range – Moderately Severe Level. Excessive black smoke has been detected exiting the engine and entering the aftertreatment diesel particulate filter.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2754 PID: SPN: 81 FMI: 16 Engine Particulate Filter Inlet Pressure – Data Valid but Above Normal Operational Range – Moderately Severe Level. Excessive black smoke has been detected exiting the engine and entering the aftertreatment diesel particulate filter.

  Cumminz

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 1663 PID: SPN: 3241 FMI: 11 Catalyst Inlet Temperature Sensor Swapped with Outlet – Condition Exists. The inlet and outlet catalyst temperature sensor connections are swapped.

  DTC TRUCKS

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 431 PID: SID 230 SPN: 558 FMI: 2 Accelerator Pedal or Lever Idle Validation Circuit – Data Erratic, Intermittent, or Incorrect. Voltage detected simultaneously on both idle validation and off-idle validation switches.

  DTC TRUCKS

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 2635 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Condition Exists. A calibration mismatch between the VGT actuator and the ECM has been detected.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Allison 1000 and 2000 Series Gen 4 (2005-11) Service manual

  Allison $10.00

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 1663 PID: None SPN: 3241 FMI: 11 Catalyst Inlet Temperature Sensor Swapped with Outlet – Condition Exists. The inlet and outlet catalyst temperature sensor connections are swapped.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2198 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Root Cause Not Known. Intermittent communication between the smart VGT controller and the ECM has been detected.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 427 PID: SID 231 SPN: 639 FMI: 9 J1939 Datalink – Abnormal Update Rate. Communication between the electronic control module (ECM) and another device on the SAE J1939 data link has been lost.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 731 PID: SID 64 SPN: 723 FMI: 7 Engine Speed/Position Camshaft and Crankshaft Misalignment – Mechanical System Not Responding or Out of Adjustment.

  Cumminz

  Rated 0 out of 5
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 731 PID: SID 064 SPN: 723 FMI: 7 Engine Speed/Position Camshaft and Crankshaft Misalignment – Mechanical System Not Responding Properly or Out of Adjustment. Engine position signal from the engine speed sensor and camshaft position sensor do not match.

  DTC TRUCKS

  Rated 0 out of 5
• 

  PACCAR PX-8 CM2150 (2007-09) Fault Code: 2635 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Condition Exists. A calibration mismatch between the VGT actuator and the ECM has been detected.

  DTC TRUCKS

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2635 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Condition Exists. A calibration mismatch between the VGT actuator and the ECM has been detected.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 649 PID: SID 115 SPN: 1378 FMI: 11 Engine Oil Change Interval – Condition Exists. Change engine oil and filter.

  Cumminz

  Rated 0 out of 5
• 

  PACCAR PX-8 CM2150 (2007-09) Fault Code: 1663 PID: SPN: 3241 FMI: 11 Catalyst Inlet Temperature Sensor Swapped with Outlet – Condition Exists. The inlet and outlet catalyst temperature sensor connections are swapped.

  DTC TRUCKS

  Rated 0 out of 5