Cummins ISL CM850 (2003-06) Fault Code: 324 PID: SID 3 SPN: 653 FMI: 5 Injector Solenoid Driver Cylinder 3 Circuit – Current Below Normal or Open Circuit. High resistance or no current detected at number 3 injector or RETURN pin.
Cummins ISL CM850 (2003-06) Fault Code: 324 PID: SID 3 SPN: 653 FMI: 5 Injector Solenoid Driver Cylinder 3 Circuit – Current Below Normal or Open Circuit. High resistance or no current detected at number 3 injector or RETURN pin.
1)Fault activation: The ECM senses current as each injector is actuated. If the ECM detects a persistent circuit error on an injector circuit, this fault will become active. If a circuit error is determined to cause excessive current, the ECM will disable the injection event for the faulty cylinders(s).
2)Fault deactivation: The ECM will attempt to enable any disabled injector circuit whenever the engine is started and approximately once per minute while the engine is running. If an injector circuit fault is active and the faulty condition is repaired, the fault will become inactive once the engine is restarted or if the engine is permitted to idle for more than a minute.
3)If a fault condition is intermittent and especially if more than one injector fault code is in the ECM memory, look for a wire harness that can short to components inside the rocker housing or for a short circuit to ground in the injector solenoid.
4)If more than one injector fault code is occurring and the faults occur for injector circuits in the same bank, a short circuit exists.
5)If the faults occur intermittently or faults occur, the engine can exhibit a misfire even if the injector circuit fault code does not always register. If a single cylinder exhibits misfires, look for an open circuit problem. If several cylinders on the same bank exhibit misfires, look for a short circuit anywhere in the bank of cylinders.
Causes of a single injector fault are:
1)An open circuit in the engine harness(es) or injector solenoid
2)High resistance in a single injector or injector solenoid
3)Extremely low resistance in an injector solenoid (injector shorted internally but not to ground)
4)Damaged ECM
5)An intermittent short.
An intermittent short can result if the wiring harness insulation rubs through near a rocker lever. An intermittent short can cause a single injector fault code. For example, a short on the harness to cylinder number 1 causes a fault code for cylinder number 2 or cylinder number 3.
Causes of multiple injector fault codes in the same bank of injectors are:
1)Short circuit in the engine harness(es) – either shorts to ground or to other wires in the engine harness
2)Short circuit in any of the three injectors in the bank – shorts to ground
3)Damaged ECM.
When looking for short circuits in the injector harnesses, pay particular attention to the wire insulation. Make sure there are no shorts to a rocker lever.
NOTE: Fault Code 951 (cylinder balance) can also be present due to this fault code.
Possible repairs:
1)Replace the engine harness.
2)Replace the injector.
3)Replace the ECM.
4)Replace the engine harness.
5)Replace injector number 1.
6)Replace injector number 2.
7)Replace injector number 3.
Related
-
volvo Devtool Studio V2 / V3 / V4 Developer tool plus 2.6 / 2.7
Trucks software $35.00Rated 0 out of 5 -
DOWNLOAD NISSAN UD DIESEL PC-CONSULT DIAGNOSTIC 1.1.13 & PC-REPROMASTER 1.2.0
NISSAN UD $100.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5 -
Detroit Diesel Diagnostic Link DDDL 8.0 PRO PROFESSIONAL Software trucks
Detroit $25.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:P0122 Pedal Position Sensor Circuit – Low Voltage
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0974 Shift Solenoid 1 (SS1) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1790 Gear Shift Module 1 Calibration Invalid
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2724 Pressure Control Solenoid 1 (PCS1) – Stuck On
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2637 Torque Management Feedback Signal – SEM
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2641 Torque Management Feedback Signal – LRTP
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2727 Pressure Control Solenoid 1 (PCS1) Control Circuit – Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0100 Lost Communication With ECM A
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2686 Actuator Supply Circuit Voltage 3 High (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0973 Shift Solenoid 1 (SS1) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P097A Shift Solenoid 1 (SS1) Control Circuit – Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0074 CAN Communications BUS 2 Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0971 Pressure Control Solenoid 3 (PCS3) Control Circuit High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2723 Pressure Control Solenoid 1 (PCS1) – Stuck Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1892 Throttle Position Sensor (TPS) PWM Signal – High Input
1000 & 2000 Gen 5Rated 0 out of 5