Cummins ISL CM850 (2003-06) Fault Code: 323 PID: SID 5 SPN: 655 FMI: 5 Injector Solenoid Driver Cylinder 5 Circuit – Current Below Normal or Open Circuit. High resistance or no current detected at number 5 injector driver or RETURN pin.
Cummins ISL CM850 (2003-06) Fault Code: 323 PID: SID 5 SPN: 655 FMI: 5 Injector Solenoid Driver Cylinder 5 Circuit – Current Below Normal or Open Circuit. High resistance or no current detected at number 5 injector driver or RETURN pin.
1)Fault activation: The ECM senses current as each injector is actuated. If the ECM detects a persistent circuit error on an injector circuit, this fault will become active. If a circuit error is determined to cause excessive current, the ECM will disable the injection event for the faulty cylinders(s).
2)Fault deactivation: The ECM will attempt to enable any disabled injector circuit whenever the engine is started and approximately once per minute while the engine is running. If an injector circuit fault is active and the faulty condition is repaired, the fault will become inactive once the engine is restarted or if the engine is permitted to idle for more than a minute.
3)If a fault condition is intermittent and especially if more than one injector fault code is in the ECM memory, look for a wire harness that can short to components inside the rocker housing or for a short circuit to ground in the injector solenoid.
4)If more than one injector fault code is occurring and the faults occur for injector circuits in the same bank, a short circuit exists.
5)If the faults occur intermittently or faults occur, the engine can exhibit a misfire even if the injector circuit fault code does not always register. If a single cylinder exhibits misfires, look for an open circuit problem. If several cylinders on the same bank exhibit misfires, look for a short circuit anywhere in the bank of cylinders.
Causes of a single injector fault are:
1)An open circuit in the engine harness(es) or injector solenoid
2)High resistance in a single injector or injector solenoid
3)Extremely low resistance in an injector solenoid (injector shorted internally but not to ground)
4)Damaged ECM
5)An intermittent short.
An intermittent short can result if the wiring harness insulation rubs through near a rocker lever. An intermittent short can cause a single injector fault code. For example, a short on the harness to cylinder number 1 causes a fault code for cylinder number 2 or cylinder number 3.
Causes of multiple injector fault codes in the same bank of injectors are:
1)Short circuit in the engine harness(es) – either shorts to ground or to other wires in the engine harness
2)Short circuit in any of the three injectors in the bank – shorts to ground
3)Damaged ECM.
When looking for short circuits in the injector harnesses, pay particular attention to the wire insulation. Make sure there are no shorts to a rocker lever.
NOTE: Fault Code 951 (cylinder balance) can also be present due to this fault code.
Possible repairs:
1)Replace the engine harness.
2)Replace the injector.
3)Replace the ECM.
4)Replace the engine harness.
5)Replace injector number 4.
6)Replace injector number 5.
7)Replace injector number 6.
Related
-
Bobcat Service Library [03.2019] Service, Operator, Maintenance, Bulletines, etc full update
Bobcat $110.00Rated 0 out of 5 -
2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )
Trucks software $85.00Rated 0 out of 5 -
JPRO 2022 v1 Commercial Vehicle Diagnostics V1 Software Download & Installation Service ( 1 PC )
JPRO $94.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:P2763 TCC PCS Control Circuit High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2641 Torque Management Feedback Signal – LRTP
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2724 Pressure Control Solenoid 1 (PCS1) – Stuck On
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2789 Clutch Adaptive Learning at Limit
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2669 Actuator Supply Voltage 2 Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0977 Shift Solenoid 2 (SS2) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2730 Pressure Control Solenoid 1 (PCS1) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2684 Actuator Supply Circuit Voltage 3 Open (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2729 Pressure Control Solenoid 1 (PCS1) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2637 Torque Management Feedback Signal – SEM
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0970 Pressure Control Solenoid 3 (PCS3) Control Circuit Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2686 Actuator Supply Circuit Voltage 3 High (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0100 Lost Communication With ECM A
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0971 Pressure Control Solenoid 3 (PCS3) Control Circuit High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2671 Actuator Supply Voltage 2 (HSD2) – High (Batt)
1000 & 2000 Gen 5Rated 0 out of 5
-
SERVICE MANUAL DETROIT DIESEL DDEC III-IV Single ECM Troubleshooting Guide
DETROIT $48.00Rated 0 out of 5