Cummins ISL CM850 (2003-06) Fault Code: 2963 PID: 110 SPN: 110 FMI: 15 Engine Coolant Temperature High – Data Valid but Above Normal Operational Range – Least Severe Level. Engine coolant temperature signal indicates coolant temperature is above the engine coolant temperature engine protection warning limit.

Related products

• 

  Cummins ISB4.5 CM2150 Fault Code: 111 PID: 629 FMI:12 Engine Control Module Critical Internal Failure – Bad Intelligent Device or Component

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2555 PID: SPN: 729 FMI: 3 Engine Intake Air Heater 1 Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2266 PID: SID 126 SPN: 1075 FMI: 4 Electric Lift Pump for Engine Fuel Supply Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 3737 PID: SID 115 SPN: 1675 FMI: 11 Engine Starter Mode Overcrank Protection – Condition Exists.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 3735 PID: SPN: 2884 FMI: 9 Engine Auxiliary Governor Switch – Abnormal Update Rate.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2363 PID: SID 29 SPN: 1073 FMI: 4 Engine Brake Actuator Driver Output 2 Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2322 PID: SID 64 SPN: 723 FMI: 2 Engine Camshaft Speed/Position Sensor – Data Erratic, Intermittent, or Incorrect.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 731 PID: SID 64 SPN: 723 FMI: 7 Engine Speed/Position Camshaft and Crankshaft Misalignment – Mechanical System Not Responding or Out of Adjustment.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 3541 PID: SPN: 51 FMI: 4 Engine Intake Throttle Actuator Position Sensor Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2371 PID: SPN: 1074 FMI: 3 Engine (Exhaust) Brake Driver Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 778 PID: SPN: 723 FMI: 2 Engine Camshaft Speed/Position Sensor – Data Erratic, Intermittent, or Incorrect.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 4284 PID: SPN: 5793 FMI: 9 Desired Engine Fueling State – Abnormal Update Rate.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 3141 PID: 102 SPN: 3667 FMI: 4 Engine Air Shutoff Sensor Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 2182 PID: 478 SPN: 1072 FMI: 3 Engine Brake Actuator Driver 1 Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz

  Rated 0 out of 5
• 

  Cummins ISB4.5 CM2150 Fault Code: 3555 PID: SPN: 1081 FMI: 9 Engine Wait to Start Lamp – Abnormal Update Rate.

  Cumminz

  Rated 0 out of 5