Cummins ISL CM850 (2003-06) Fault Code: 1845 PID: SPN: 97 FMI: 3 Water-in-Fuel Indicator Sensor Circuit – Voltage Above Normal or Shorted to High Source (For Generator Engines Only). High voltage detected at the water-in-fuel indicator circuit.
Cummins ISL CM850 (2003-06) Fault Code: 1845 PID: SPN: 97 FMI: 3 Water-in-Fuel Indicator Sensor Circuit – Voltage Above Normal or Shorted to High Source (For Generator Engines Only). High voltage detected at the water-in-fuel indicator circuit.
The water-in-fuel sensor is located in the Stage 1 filter housing. It is a serviceable part.
Possible causes:
1)Open return or signal circuit in the harness, connectors, or sensor.
2)SIGNAL wire shorted to sensor supply or battery voltage.
Possible repairs:
1)Replace the damaged section of harness or damaged water-in-fuel indicator sensor.
2)Replace the water-in-fuel indicator sensor.
3)The removal and installation of the connector may correct the fault.
4)Replace the ECM.
5)Replace the damaged section of the engine harness.
6)Replace the damaged section of the engine harness.
-
download MANCATS II v14.01 2014 Diagnostic software MAN CATS ( virtual machine )
MAN $75.00Rated 0 out of 5
-
Volvo PROSIS Offline 2019 Parts Catalog Installation Service
Trucks software $45.00Rated 0 out of 5 -
Scania SDP3 2.48.6 Diagnosis & Programming for VCI 3 VCI3 without Dongle
Scania $30.00Rated 0 out of 5 -
premium volvo tech tool update 2.8.150 diagnostic software 1pc
Trucks software $150.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:P2685 Actuator Supply Circuit Voltage 3 Low (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2669 Actuator Supply Voltage 2 Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Detroit DD13 GHG14 (2014-16) Fault Code: SPN 511403 FMI 9 (CPC) Generator (Charging System) Terminal W – Allocation Error (Pulse/Rev Signal)
DD13 GHG14 (2014-16)Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2671 Actuator Supply Voltage 2 (HSD2) – High (Batt)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2724 Pressure Control Solenoid 1 (PCS1) – Stuck On
1000 & 2000 Gen 5Rated 0 out of 5 -
Detroit DD13 GHG14 (2014-16) Fault Code: SPN 511403 FMI 10 (CPC) Generator (Charging System) Terminal W – Low Voltage
DD13 GHG14 (2014-16)Rated 0 out of 5 -
Detroit DD16 GHG14 (2014-16) Fault Code: SPN 511403 FMI 10 (CPC) Generator (Charging System) Terminal W – Low Voltage
DD16 GHG14 (2014-16)Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2723 Pressure Control Solenoid 1 (PCS1) – Stuck Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Detroit DD16 GHG14 (2014-16) Fault Code: SPN 511403 FMI 9 (CPC) Generator (Charging System) Terminal W – Allocation Error (Pulse/Rev Signal)
DD16 GHG14 (2014-16)Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2764 TCC PCS Control Circuit Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2761 TCC PCS Control Circuit Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2637 Torque Management Feedback Signal – SEM
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2727 Pressure Control Solenoid 1 (PCS1) Control Circuit – Open
1000 & 2000 Gen 5Rated 0 out of 5
-
MANUAL SERVICE Deutz Combine 5650 H, 5660 HTS5670 H / HTS5680 H, 5690 HTS
DEUTZ $38.00Rated 0 out of 5 -
SERVICE MANUAL Eaton Gen III Automated TransmissionsTRSM0930 EN-USOctober 2020
TRUCK MANUALS $24.00Rated 0 out of 5 -
SERVICE MANUAL International Engines MaxxForce DT 9 10 (2007-2009)
INTERNATIONAL ENGINES $30.00Rated 0 out of 5