Cummins ISB4.5 CM2150 Fault Code: 1911 PID: 157 SPN: 157 FMI: 0 Injector Metering Rail Number 1 Pressure – Data Valid but Above Normal Operating Range – Most Severe Level.

Circuit Description
The engine control module (ECM) monitors engine operating conditions, including the reading of rail fuel pressure, and changes the flow command to either increase (OPEN the fuel pump actuator) or decrease (CLOSE the fuel pump actuator) the fuel supply to the high-pressure pump.

Component Location
The fuel pump actuator is installed on the high-pressure fuel pump. The high-pressure relief valve is located on the fuel rail.

Conditions for Running the Diagnostics
This diagnostic runs continuously when the engine is operating.

Conditions for Setting the Fault Codes
The ECM has detected that the measured fuel rail pressure is above the commanded fuel rail pressure by a calibrated limit.

Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE light and/or the malfunction indicator lamp (MIL) immediately when the diagnostic runs and fails.

Conditions for Clearing the Fault Code
-To validate the repair, start the engine and let it idle for 1 minute.
-The ECM will turn off the amber CHECK ENGINE light immediately after the diagnostic runs and passes.
-The ECM will turn off the MIL after three consecutive ignition cycles that the diagnostic runs and passes.
-This fault code and MIL can also be cleared with INSITE™ electronic service tool.

Shop Talk
In normal engine operation, the ECM calibration varies the flow commanded to the fuel pump actuator to achieve the correct fuel rail pressure. System failures that cause loss of pressure control can cause the fuel rail pressure relief valve to open. The fuel rail pressure relief valve acts to protect the high-pressure components from over-pressurization. If the ECM detects that the fuel rail pressure relief valve is open without detection of a fuel pump actuator circuit error, Fault Code 1911 will become active. On certain applications, the ECM will attempt to reset automatically causing a momentary loss of power for less than 1 second.

Possible Causes
-Purging air through the fuel system can cause a pressure overshoot, therefore causing Fault Code 1911 to log. A few bubbles exiting the line during the air in fuel test is expected. A foamy appearance is an indication of a leak that allows air to enter, a severe inlet restriction that causes cavitation, or a system that is not yet primed. If fuel inlet restriction is not excessive, the source of air entry should be isolated to one of the following: Suction fuel lines, OEM fuel lines, suction-side fuel filter assemblies, or stand-pipe(s) in the fuel tank(s).
Sustained periods of very low pressure under load followed by pressure recovery overshoot. This can be caused by high restriction due to plugged filters (Fault Code 559).
-A tampered fuel pressure sensor that reads low, a biased pressure sensor, or a poor electrical connection.
-If an intermittent electrical circuit problem with the fuel pump actuator circuit exists, it is possible for Fault Code 1911 to become active, then inactive, during normal engine operation. ECM Fault Code 2311 is designed to detect electrical circuit issues with the actuator. Therefore, it is only necessary to inspect for bad connectors or harness issues for Fault Code 1911 if no other fault codes exist. A fuel pump actuator with excessive leakage will result in high rail fuel pressures at idle or light load.
-Other conditions include ECM wiring harness issues such as poor grounds, battery voltage spikes, electrical noise, low alternator output, and large disturbances of battery voltage, as when jump-starting the vehicle.
-The fuel rail pressure sensor should also be checked. When checking the fuel rail pressure sensor accuracy, make sure the high-pressure fuel rail is not pressurized. The fuel pump, high-pressure fuel lines, and fuel rail contain very high-pressure fuel. Do not loosen any fittings while the engine is operating. Wait at least 10 minutes after shutting down the engine before loosening any fittings in the high-pressure fuel system to allow pressure to decrease to a lower level. There could be a significant amount of time waiting on the rail to depressurize to zero on some engines. In such cases, it may be necessary to manually relieve the pressure from the high-pressure fuel rail.