Cummins ISB CM850 (2003-06) Fault Code: 1657 PID: SPN: 1326 FMI: 11 Engine Misfire Cylinder 4 – Condition Exists. Engine misfire has been detected in cylinder number 4.
Cummins ISB CM850 (2003-06) Fault Code: 1657 PID: SPN: 1326 FMI: 11 Engine Misfire Cylinder 4 – Condition Exists. Engine misfire has been detected in cylinder number 4.
If Fault Code 1657 is inactive in the ECM memory and there is no complaint such as ?low power? or ?engine misfire?, it is possible that an intermittent event such as air entering the fuel system following a filter change caused the fault. Inactive counts of Fault Code 1654 should be disregarded unless other performance symptoms are present. The engine coolant temperature must be greater than 71?C [160?F] before this diagnostic will run.
Causes of cylinder misfire can include:
1)Valve lash out of specification (compare actual valve lash to reset limits)
2)Cylinder failure (check for high blowby when the engine is loaded)
3)Valve failure or valve held open (listen for intake valve ?chirping? noise in the intake)
4)Cylinder head or gasket failure (look for signs of oil, coolant, or casting flash in the intake or exhaust passages)
5)Extreme camshaft wear (inspect the camshaft lobes for wear)
6)Extra, missing, or damaged sealing washer under an injector
7)Injector failures (?swap? injectors to see if the problem ?follows? the indicated injector).
8)Check air compressor timing (if engine has had fault since new or has had a recent air compressor replacement.)
9)For 6 cylinder ISBe4 automatic transmission applications: Check ?On-Board Diagnostic (OBD) misfire alternate gains? setting in the features and parameters screen in INSITE? electronic service tool. If the vehicle is fitted with a Voith transmission, this should be set to 2. All others are set to 1.
On-Board Diagnostic Information:
1)The ECM illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails
2)The ECM turns OFF the MIL after 3 consecutive ignition cycles, with the engine running for at least 10 seconds, that the diagnostic runs and does not fail. The MIL lamp and fault code can also be cleared, use the INSITE? electronic service tool
3)The fault code will be cleared from the memory after 40 consecutive drive cycles when the diagnostic runs and passes.
Possible repairs:
1)Replace the cylinder number 4 injector.
Related
-
JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023
John Deere $250.00Rated 0 out of 5 -
Bobcat Service Library [03.2019] Service, Operator, Maintenance, Bulletines, etc full update
Bobcat $110.00Rated 0 out of 5 -
VOLVO PREMIUM TECH TOOL PTT 2.7.30 Developer + Devtool + INSTALATION VIDEO!
Trucks software $60.00Rated 0 out of 5
-
PACCAR Electronic Service Analyst 5.4.3.0 SW files 27.03.2021 software trucks
PACCAR $60.00Rated 0 out of 5 -
Detroit Diesel Diagnostic Link DDDL 8.0 PRO PROFESSIONAL Software trucks
Detroit $25.00Rated 0 out of 5 -
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5 -
Navistar international OnCommand service information 2018 software trucks
Navistar $50.00Rated 0 out of 5
Related products
-
SERVICE MANUAL International Engines MaxxForce 7 (2007-2009)
INTERNATIONAL ENGINES $31.00Rated 0 out of 5 -
SERVICE MANUAL International Engines DT466E & DT530E (1999 & Older)
INTERNATIONAL ENGINES $31.00Rated 0 out of 5