CAT 3126E Fault Code: 108-04 PID: Flash Code 26 SPN: 108 FMI: 4 Barometric Pressure voltage low
The Engine Control Module (ECM) detects the following conditions:
•The signal voltage from the atmospheric pressure sensor is less than 0.2 VDC for more than 30 seconds.
•The ECM has been powered for at least two seconds.
•The engine is not running or the engine has been running for more than ten seconds.
The Engine Control Module (ECM) continuously creates a pull-up voltage on the signal wire for each sensor. The ECM uses this pull-up voltage in order to detect a problem in the signal circuit. When the ECM detects voltage that is above a threshold on the signal wire, the ECM activates a -3 diagnostic code. When the ECM detects voltage that is below a threshold on the signal wire, the ECM activates a -4 diagnostic code.
Note: When you check for a diagnostic code, be sure to wait at least 30 seconds.
The most likely cause of a code is a problem with an electrical connector or wiring. The least likely cause of a code is the ECM.
The following sensors are included in this code:
Fuel pressure sensor
Injection actuation pressure sensor
Barometric pressure sensor
Boost pressure sensor
Engine oil pressure sensor
Probable Causes:
1) ECM Connection
2) Sensor failure
3) Sensor harness/connector
4) ECM Failure
-
volvo Devtool Studio V2 / V3 / V4 Developer tool plus 2.6 / 2.7
Trucks software $35.00Rated 0 out of 5 -
Scania SDP3 2.48.6 Diagnosis & Programming for VCI 3 VCI3 without Dongle
Scania $30.00Rated 0 out of 5
-
2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )
Trucks software $85.00Rated 0 out of 5 -
download Hitachi Construction Machinery MPDr Ver 3.7.0.0 [10.2020] Diagnostic Software
Hitachi $76.00Rated 0 out of 5 -
Wabco ToolBox plus 13.7 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5 -
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2
Trucks software $35.00Rated 0 out of 5 -
International Truck ISIS – Oncommand Service Information Q4.2020 [04.2020]
Navistar $85.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino $60.00Rated 0 out of 5 -
DOWNLOAD NISSAN UD DIESEL PC-CONSULT DIAGNOSTIC 1.1.13 & PC-REPROMASTER 1.2.0
NISSAN UD $100.00Rated 0 out of 5 -
CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT $45.00Rated 0 out of 5
Related products
-
CAT 3126B Fault Code: 168-01 PID: Flash Code 51 SPN: 168 FMI: 1 Low ECM Battery Power
3126BRated 0 out of 5 -
CAT 3126B Fault Code: 231-02 PID: Flash Code 58 SPN: 639 FMI: 2 J1939 Data Incorrect
3126BRated 0 out of 5 -
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5 -
CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )
CAT $65.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce DT 9 10 (2014 & Newer)
INTERNATIONAL ENGINES $17.00Rated 0 out of 5