Allison 3000 & 4000 Gen 4 Fault Code: P0975 Shift Solenoid 2 (SS2) Control Circuit Open
DIAGNOSTIC RESPONSE:
7-speed: Allow 2 through 6, N, R
CIRCUIT DESCRIPTION:
The Shift Solenoid 2 (SS2) may either be assigned to retarder models with an air solenoid or to the SS2 required in 7-speed models. For retarder models with an accumulator, the Transmission Control Module (TCM) commands SS2 ON to enable the normally closed air solenoid which allows air pressure to stroke the accumulator piston to pre-fill the retarder cavity during retarder operation. For 7-speed models, the TCM commands the SS2 solenoid ON to send main pressure to both the C2 latch valve and the C6 interlock valve. The TCM sends control current to the solenoid from the High Side Driver 3 (HSD3) through wire 131. HSD3 is continuously ON unless the TCM detects a fault condition. Wire 119 completes the circuit between the solenoid and the TCM low side driver for SS2. The TCM energizes the solenoid by switching the solenoid’s low side driver ON. DTC P0975 indicates that the TCM has detected an open condition in the SS2 solenoid electrical circuit. The open condition may exist in the high side (wire 131) or low side (wire 119).
CONDITIONS FOR RUNNING THE DTC:
TCM initialized normally and engine speed above 200 rpm.
CONDITIONS FOR SETTING THE DTC:
This DTC sets when the TCM detects SS2 low side driver has been detected in a failed open state.
ACTION TAKEN WHEN THE DTC SETS:
When DTC P0975 is active:
1. For 7-speed models, limit ranges to Reverse (R) and ranges 2-6 operation.
2. TCM commands retarder OFF.
3. The TCM inhibits TCC engagement.
4. DTC is stored in the TCM history.
5. The CHECK TRANS light illuminates.
6. The TCM freezes shift adapts (DNA).
CONDITIONS FOR CLEARING THE DTC:
Use the diagnostic tool to clear the DTC history. The TCM automatically clears the DTC from the TCM history if the vehicle completes 40 warm-up cycles without failure.
DIAGNOSTIC AIDS:
DTC P0975 can be caused by:
1. SS2 (7-speed only) issues such as:
– W119 high resistance or open circuit in chassis harness.
– W119 (terminal 17 of 20-way) high resistance or open circuit in internal transmission harness.
2. Air solenoid (SS2) issues such as:
– W119 high resistance or open circuit in chassis harness.
3. Defective air solenoid (SS2).
4. Unlocked connectors, expanded terminals, poor pin crimps or unlocked pins causing high resistance or open circuit.
5. Defective TCM.
Review applicable information in Control System and Transmission Specifications to find additional circuit specifications, system and connector diagrams, and troubleshooting tips.
-
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P1892 Throttle Position Sensor Pulse Width Modulation (PWM) Signal High Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0218 Transmission Fluid Over Temperature Condition
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL Eaton Gen III Automated TransmissionsTRSM0930 EN-USOctober 2020
TRUCK MANUALS $24.00Rated 0 out of 5 -
SERVICE MANUAL International Engines DT466 (2004-2006)
INTERNATIONAL ENGINES $45.00Rated 0 out of 5