Allison 3000 & 4000 Gen 4 Fault Code: P088A Transmission Filter Maintenance Alert
DIAGNOSTIC RESPONSE:
None
CIRCUIT DESCRIPTION:
The Filter Life Monitor (FM) feature alerts the driver when a filter change is needed by illuminating the SERVICE TRANS indicator (wrench icon display). FM also activates any OEM-provided SERVICE TRANS indicator or datalink message center display (when integrated to receive the message). If the filter is detected as restricted, the wrench icon in the selector flashes ON and OFF for approximately 2 minutes the first time D (Drive) is selected after each engine start. Also, DTC P088A becomes active concurrently with these other visible filter maintenance alerts. This DTC monitors the electrical state of the PS2 FLI pressure switch. If PS2 is detected as open (pressurized) while the transmission is in a forward range and with the Torque Converter Clutch (TCC) (lockup) solenoid energized, the DTC becomes active.
The difference between main pressure (before the filter) and TCC lockup pressure determines whether to stroke or de-stroke the FLI pressure switch valve in the prognostics valve body within the control valve module. An open switch with the TCC solenoid energized causes an active DTC P088A. The CHECK TRANS light does not illuminate for this DTC.
An active DTC and SERVICE TRANS indicator occurs at next engine start when the operator selects D (Drive).
ACTION TAKEN WHEN THE DTC SETS:
1. DTC P088A is stored in the TCM history for a number of ignition cycles.
2. The wrench icon in the shift selector display will flash ON and OFF for approximately 2 minutes the first time D (Drive) is selected after each engine start.
CONDITIONS FOR CLEARING THE DTC:
1. The feature is designed to reset itself automatically after the main filter has been changed.
2. The diagnostic tool can clear the DTC from TCM history.
3. The operator may clear the code and flashing SERVICE TRANS indicator by pressing the MODE button for 10 seconds provided the CMG to disable a reset from the shift selector was not enabled. However, if the filters are not changed, the DTC will most likely become active again.
4. FM may also be reset by selecting N-R-N-R-N-D-N on the shift selector, pausing briefly (less than 3 seconds) between each selector movement when the ignition is on and the engine not running.
5. FM may be reset with a SAE J1939 message.
6. Use the diagnostic tool to clear the DTC from the TCM history. The TCM automatically clears the DTC from the TCM history if the vehicle completes 40 warm-up cycles without the DTC recurring.
DIAGNOSTIC AIDS:
Refer to the OEM 4th Generation Control System Operation and Prognostics Package and Features for important information about OM, FM, and TM. These discuss prognostics principles of operation, feature requirements, maintenance alerts, reports, and processes to reset features or change fluid type (January 2010 and later TCM software) using either the OEM or an OEM-supplied (MY09 and later) shift selector.
The diagnostic tool will show PS2 PRESSURIZED when PS2 is open and PS2 EXHAUSTED when PS2 is closed.
DTC P088A can be caused by:
1. Restricted Main Filter.
NOTE: Change both main and lube filters if main filter is restricted.
2. Low lockup pressure.
3. Open or high resistance in W118 or W158 in chassis harness.
4. Open or high resistance from terminal 17 to PS2, or from PS2 to terminal 19, in control module wire harness.
5. Issue with PS2.
6. Issue with TCM.
Related
-
CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )
CAT $65.00Rated 0 out of 5
-
DAF Davie Runtime v5.6.1 Davie XDc ll [02.2019] + Expire Fix 302.00 Unlock ( Windows 7 )
DAF $70.00Rated 0 out of 5 -
DOWNLOAD NISSAN UD DIESEL PC-CONSULT DIAGNOSTIC 1.1.13 & PC-REPROMASTER 1.2.0
NISSAN UD $100.00Rated 0 out of 5 -
JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023
John Deere $250.00Rated 0 out of 5 -
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2
Trucks software $35.00Rated 0 out of 5 -
CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT $45.00Rated 0 out of 5 -
ddct Detroit diesel calibration tool (DDCT) v4.5 English Include Calibrations & Metafiles
Detroit $30.00Rated 0 out of 5 -
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0123 Pedal Position Sensor Circuit High Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2773 Torque Control Request Ignored – ECM/TCM
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1892 Throttle Position Sensor Pulse Width Modulation (PWM) Signal High Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL Eaton Fuller® HD FR/FRO TransmissionsTRSM2400April 2013
TRUCK MANUALSRated 0 out of 5