Allison 1000 & 2000 Gen 4 Fault Codes: P0732 Incorrect 2nd Gear Ratio
Allison 1000 & 2000 Gen 4 Fault Codes: P0732 Incorrect 2nd Gear Ratio
CIRCUIT DESCRIPTION:
The Transmission Control Module (TCM) uses input from the turbine speed sensor and output speed sensor to determine gear ratios. The TCM then compares the known gear ratio to the calculated gear ratio for the current range.
CONDITIONS FOR RUNNING THE DTC:
1. Output speed exceeds 200 rpm.
2. Second range is selected and attained.
3. DTC P0716, P0717, P0721, or P0722 is not active.
CONDITIONS FOR SETTING THE DTC:
DTC P0732 sets when the calculated second range ratio (steady state) differs from the known second range ratio.
ACTION TAKEN WHEN THE DTC SETS:
When DTC P0732 is active, the following conditions will occur:
1. The transmission will fail to 3rd range.
2. If the shift selector is moved to N (Neutral), the transmission will shift to N (Neutral).
3. If the shift selector is moved to R (Reverse), the transmission will shift to R (Reverse) unless the transmission is compromised by overspeeding or a direction change; then it will lock in N (Neutral).
DTC P0732 is stored in the TCM history.
The CHECK TRANS light illuminates.
The TCM freezes shift adapts (DNA).
The TCM inhibits TCC engagement.
CONDITIONS FOR CLEARING THE DTC/CHECK TRANS LIGHT:
A Scan Tool may be used to clear the code from the TCM history. The TCM automatically clears the DTC from the TCM history if the vehicle completes 40 warm-up cycles without the DTC recurring.
DIAGNOSTIC AIDS:
1. Incorrect ratio codes typically indicate mechanical problems with specific clutches, i.e. C1 and C4 for 2nd range.
2. An incorrect ratio code could indicate a hydraulically failed solenoid. Check the DTC information for the specific solenoid.
3. You may have to drive the vehicle to experience the fault. Clutch test mode can be used to check stall speed.
4. Incorrect TCM calibrations will cause this DTC to set. Verify that the proper TCM calibration is being used with the correct transmission family (there are different gear ratios for the 1000 and 2000 Product Families transmissions).
Related
$50.00
-
premium volvo tech tool update 2.8.150 diagnostic software 1pc
Trucks software $150.00Rated 0 out of 5
-
CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )
CAT $65.00Rated 0 out of 5 -
Volvo PROSIS Offline 2019 Parts Catalog Installation Service
Trucks software $45.00Rated 0 out of 5 -
JPRO 2022 v1 Commercial Vehicle Diagnostics V1 Software Download & Installation Service ( 1 PC )
JPRO $94.00Rated 0 out of 5 -
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5 -
Hino Diagnostic eXplorer 2 – Hino DX2 1.1.19.1 with keygen unlocked ( Hino trucks )
Hino $50.00Rated 0 out of 5 -
JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023
John Deere $250.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0875 Transmission Reverse Pressure Switch Circuit Malfunction
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1301 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL Eaton Gen III Automated TransmissionsTRSM0930 EN-USOctober 2020
TRUCK MANUALS $24.00Rated 0 out of 5